background image

 
Cirrus™ User Manual 

2010-08-09

 

 

Safety Instructions 

 

 

 

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that 
they also receive this instruction booklet. 

 

Always make sure that you are connecting to the proper voltage, and that the line voltage you are 
connecting to is not higher than that stated on the decal or rear panel of the fixture. 

 

This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to 
rain or moisture. 

 

Make sure there are no flammable materials close to the unit while operating. 

 

The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent 
surfaces. Be sure that no ventilation slots are blocked. 

 

Always disconnect from power source before servicing or replacing fuse and be sure to replace with 
same fuse size and rating. 

 

Secure fixture to fastening device using a safety chain. 

 

Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher 
than this.  

 

In the event of a serious operating problem, stop using the unit immediately. Never try to repair the 
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please 
contact the nearest authorized technical assistance center. 

 

Never connect the device to a dimmer pack. 

 

Make sure the power cord is never crimped or damaged. 

 

Never disconnect the power cord by pulling or tugging on the cord. 

 

Avoid direct eye exposure to the light source while it is on.  

 

Lasers can be hazardous and have unique safety considerations. Permanent eye injury and 
blindness is possible if lasers are used incorrectly. Pay close attention to each safety REMARK and 
WARNING statement in the user manual. Read all instructions carefully BEFORE operating this 
device. 

 

Caution! 

Avoid direct eye contact with laser light. Never intentionally expose your eyes or others to 
direct laser light. 

 
Caution! 

This laser product can potentially cause instant eye injury or blindness if laser light directly 
strikes the eyes. 

 
Caution! 

It is illegal and dangerous to shine this laser into audience areas, where the audience or other 
personnel could get direct laser beams or bright reflections into their eyes. 

 

Caution!   

It is a US Federal offense to shine any laser at aircraft. 

 
Caution! 

Use of controls or adjustments or performance of procedures other than those specified 
herein may result in hazardous radiation exposure.

 

 
Caution! 

There are no user serviceable parts inside the unit. Do not open the housing or attempt any 
repairs yourself. In the unlikely event your unit may require service, please contact the dealer 
nearest to you. 

 
 

 

Please read these instructions carefully, which includes important 
information about the installation, usage and maintenance of this product. 

Summary of Contents for Cirrus

















Reviews: