background image

ASSEMBLY GUIDE 

GRILL FINAL Assembly

           

Part 

 

Qty

.  

C4

–  Controller

 

Step 1 

Install the

 Controller (C4)

 into the receptacle. Be sure to route the controller cord behind the towel bar when 

installing the controller. The control knob should be facing up as you engage the tip of the controller into the receptacle. 

Congratulations!

 You have successfully completed the 

assembly of your grill. 

NOTE: 

Be sure to press the controller into the receptacle as far as it will go. Route the 

controller cord BEHIND the towel bar as shown.

C4 

Receptacle

Controller

Controller Tip

Towel Bar

Ground Fault Interrupter

?

 Since 1971 the National Electric Code (NEC) has 

required Ground Fault Interrupter devices on all 
outdoor circuits.

?

If your residence was built before 1971, check with a 

qualified electrician to determine if a Ground Fault 
Interrupter protector exists. 

?

Do not use this appliance if the circuit does not 

have GFI  protection.

?

Do not plug this appliance into an indoor circuit.

Fasteners

 

 

 

 

(qty 2)

Fiber Washer

 

 

10-24x3/8"

 

(qty 2)

screw

Fiber

Washer

(2 each)

C5

 

10-24x3/8"

Screws

(2 each)

Step 2 

Install the 

Lid Handle

 with 2 10-24x3/8" screws and 2 fiber washers as shown. 

C5

– Lid Handle

1

Visit 

www.sizzleonthegrill.com/user-forums

 to chat with Patio Bistro

®

 owners just like you!

 

Summary of Contents for Patio Bistro 08601559-16









Reviews: