background image

First Time Use

Read your Assembly Manual and ensure the grill is put together 
properly.  Remove all Point-of-Purchase advertising material from 
all grill surfaces before first use.  We recommend operating your 
grill on its highest setting for 15-20 minutes prior to your first use.  
This aids in removing the oils used during manufacturing.

Lava Rock / Briquettes

This gas grill has been designed, engineered, and tested to be 
used with flame tamers or heat distribution plates to provide 
more even heating, improve the cleaning process, and reduce 
flare-ups.  The addition of after market lava rocks, charcoal, or 
briquettes of any type will cause poor combustion and increase 
the likelihood of a grease fire, and is not recommended.  Using 
briquettes, lava rock, or charcoal in this grill will void your 
warranty.  For extra smoke flavor, we recommend using a 
smoker box with wood chips.

Temperature

The temperature gauge in the hood of your new grill measures 
air temperature.  The air temperature inside your grill will never 
be as hot as the temperature at the cooking surface.

Note:  Since 1995, all regulators (the part that attaches to the gas 
tank to regulate the flow of gas) have included a safety feature 
that restricts gas flow in the event of a gas leak. You can 
inadvertently activate this safety feature without having a gas 
leak. This typically occurs when you turn on the gas using the 
grill control knob before you turn on the LP tank valve.  If the gas 
regulator safety feature activates, the grill will only reach 
temperatures between 250°F and 300°F even with all burners on 
the high setting.

If your grill is not getting hotter than 250°F to 300°F these 
steps should be taken first to reset the gas regulator safety 
device:

1. Open the grill lid.
2. Turn off all knobs on the control panel in front.
3. Turn off the tank knob.
4. Disconnect the regulator from the LP tank.
5. Wait 30 seconds.
6. Reconnect the regulator to the LP tank.
7. Slowly open the LP tank knob all the way. Do not put 

excessive force on the valve at the full open position to avoid 
damaging the valve.

8. Turn on the appropriate control knob and light the grill per the 

instructions on the control panel.

An illustration of this process is included in this Product Guide.  
See Troubleshooting section for additional information.

Pre-Heating Your Grill

Just like your home oven, your grill should be pre-heated to 
provide optimum performance. Pre-heat the grill on high for 10-
15 minutes – longer if weather conditions require.  Please refer to 
the lighting instructions inside the Product Guide if you have 
questions about how to light your grill.  A match-light chain and 
hole is provided for your convenience.

GRILLING GUIDE – Getting Started 

Regulator

Coupling Nut

4

Summary of Contents for 463722711

































Reviews: