background image

RF Modulator

               PLL Synthesized Oscillator 

Video                                NTSC 
Audio                                L&R Monaural/Stereo loop opt. 

RF Carriers

       

Frequency Stability        ±50KHz 
Frequency Ranges          UHF 471.25-855.25MHz 
                                          Ultraband 469.25-859.25MHz  
Channels                          UHF 14-78, Ultraband 65-135   
                                          (Excl 95-99) 
Channel Width                6.0MHz  
Audio Offset                    4.5MHz  
Sidebands                        Double  

RF Output

  

Minimum                         =>20dBmV 
Video Output                   1VPeak to Peak  
Audio Output                  1V RMS  

Video Performance

  

Differential Gain            Less than 2% (0.2dB)  
Differential Phase           Less than 3 degree  

Operating Temps

          0

o

C to 50

o

C  

Signal/Noise Ratio         Greater than 52dB  

Dimensions:

                    TBA 

Specifications 

Specifications subject to change. 

Spurious Output Rejection

  

Outside Carrier              +12MHz Greater than 70dBC  
Inside Carrier                  +12MHz Greater than 55dBC  
Isolation                          Greater than 70dB 

Inputs

  

Video                               0.4V-2.7V Peak to Peak adj. 
Audio                               1V RMS  

Connectors

  

Video Inputs                    RCA Female  
Audio Inputs                   RCA Female  
RF Output                        F type female  
Insertion Loss                  3.7dB 
Bandwidth                      5-1000MHz 

Transformer Input 

  

Input Voltage                  115 VAC, 50/60Hz /E4200-       
                                         120VAC,60Hz 
Power                               8 Watts  
Output Voltage               15VAC, 450MA (E2200, E3200) 
                                         15VDC, 450MA (E4200) 

Exterior

                           metal case and front panel  

Display

                            2 digit channel display  

Channel Selector          

Up/Down selector buttons  

Channel Vision 

Limited Warranty

 

 
Channel Vision Technology will repair or replace any defect in material or workmanship which occur during 
normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of 
original purchase.  This is a no hassle warranty with no mail in warranty card needed.  This warranty does not 
cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or 
failures due to accident, misuse, abuse, or alteration of the equipment.  This warranty extends only to the original 
purchaser.  A purchase receipt, invoice, or other proof of original purchase date will be required before warranty 
repairs are provided. 
 
Mail-in service can be obtained during the warranty period by calling toll free (800) 840-0288 toll free.  A Return 
Authorization number must be obtained in advance and be marked on the outside of the shipping carton. 
 
This warranty gives you specific legal rights, and you may have other rights (which vary from state to state).  If a 
problem with this product develops during or after the warranty period, please contact Channel Vision, your dealer, 
or any factory-authorized service center. 

Summary of Contents for E2200








Reviews: