background image

5

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with 
package contents list and hardware contents above. If any part is missing or damaged, do not 
attempt to assemble the product. Contact customer service for replacement parts.

Estimated Assembly Time: 60 minutes

Tools Required for Assembly (not included):
Phillips screwdriver w/ medium blade. Leak Detection Solution.

 WARNING

California Proposition 65
Combustion by-products produced when using
this product contain chemicals known to the State
of California to cause cancer, birth defects, and
other reproductive harm.

 WARNING

                                BURN HAZARD
• Never leave heater unattended when hot or in use.
• Keep out of reach of children.

 WARNING

• This product is fueled by propane gas. Propane gas
is invisible, odorless, and flammable. An odorant is
normally added to help detect leaks and can be 
described as a “rotten egg” smell. The odorant can 
fade over time so leaking gas is not always detectable
by smell alone.
• Propane gas is heavier than air and leaking propane
will sink to the lowest level possible. It can ignite by 
ignition sources including matches, lighters, sparks or
open flames of any kind many feet away from the 
original leak. Use only propane gas set up for vapor 
withdrawal.
• Store or use propane gas in compliance with local 
ordinances and codes or with ANS/NFPA 58. Turn off 
propane when not in use.

 WARNING

• Alert children and adults to the hazards of high surface 
temperatures. Stay away from these surfaces to avoid 
burning skin or igniting clothing.
• Carefully supervise young children when in the vicinity
of the heater.
• Do not hang clothing or any other flammable materials
from the heater, or place on or near the heater.
• Replace any guard or protective device removed for
servicing the appliance prior to placing back in service.
• Installation and repair should be done by a qualified
service person. The heater should be inspected
before use and annually by a qualified service person.
More frequent cleaning may be required as necessary.
It is imperative that the control compartment, burners,
and circulating air passageway of the appliance be
kept clean.

SAFETY INFORMATION

 CAUTION

CAUTION indicates an imminently hazardous situation
which, if not avoided, may result in minor or moderate
personal injury, or property damage.

 CAUTION

                            SERVICE SAFETY
• Keep all connections and fittings clean. Make sure
propane cylinder valve outlet is clean.
• During set up, check all connections and fittings for
leaks using soapy water. Never use a flame.
• Use as a heating appliance only. Never alter in any 
way or use with any device.

 WARNING

Certain materials or items, when stored under the 
heater, will be subjected to radiant heat and could be
seriously damaged.

Summary of Contents for NCZH-G-SS





















Reviews: