background image

5

H.  After making sure that O-ring and wave spring inside top 

of bowl are in place, reassemble bowl to head.

NOTE:

 Make certain O-ring is generously lubricated

NOTE:

 Wave spring ends should be pointed down to prevent 

the wave spring from interfering with reassembly.
I. 

Reconnect drain tube to bulkhead fitting by pushing 

tube into fitting until it locks in position.

J.  Reinstall side and top panels.
K.  Restore power and repressurize dryer. Resume 

operation.

Element o-ring

Separator Element

Bowl o-ring

Drain Mechanism

Wave Spring

Tube

Hose
Barb

3.4  Automatic condensate drain 

•  Check daily to be sure automatic drain is discharging. 
•  Replace drain mechanism yearly.

A.  Shut-off compressed air supply to the dryer and depres-

surize. Turn off power to the dryer.

B.  Remove top panel.
C.  Remove two screws holding side panel then remove side 

panel by sliding upwards.

D.  Disconnect drain tube from bulkhead fitting in cabinet 

base.  To remove, press the plastic collar in, toward the 

fitting, while pulling the tube out of the fitting. 

E.  Remove bowl - push bowl up, turn 1/8th turn to your 

left, and pull bowl straight down.

F.  Remove drain tube fitting from bottom of bowl.  
G.  Remove old drain mechanism by turning knurled fitting 

to the right (clockwise) and remove.

H.  Install new drain mechanism. If necessary, use a wire 

or pencil to guide the new mechanism into place.

I. 

Reassemble drain tube fitting to bowl.

J.  After making sure that large O-ring in filter head is in 

place, reassemble bowl to head.

K.  Reconnect drain tube to bulkhead fitting by pushing 

tube into fitting until it locks in position.

L.  Reinstall top and side panels.
M.  Restore power and repressurize dryer. Resume 

operation.

Summary of Contents for CRH 100

















Reviews: