background image

500560-UK - 2800W RATED PORTAbLE GENERATOR

IMPORTANT SAfETY INSTRUCTIONS

7

Safety Labels

These labels warn you of potential hazards that can cause serious injury. Read them carefully.

If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement.

LABEL

DESCRIPTION

A

NEVER 

use inside a home, 

garage, outbuilding or 

vehicles, 

EVEN IF

 doors 

and windows are open.

ONLY 

use

 OUTSIDE 

and far away from 

windows, doors, 

and vents.

     

DANGER

Using a generator indoors 

CAN KILL YOU IN MINUTES.

 

Generator exhaust 

contains carbon monoxide. This is a poison you cannot see or smell.

1056-BY-L-A

K

123

185

---

Colors

LPN

1056-BY-L

Rev

A

Size

158 x 113 mm

Artwork Notes

2mm safe margin

Revision Changes

This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for 
outside parties without the explicit consent of Champion Power Equipment.

Safety Symbols/ 

CO Danger

B

1058-BY-L-A

UNLEADED FUEL ONLY. 

Minimum octane

rating of 85. Maximum 

10% ethanol.

K

123

---

---

---

Colors

LPN

1058-BY-L

Rev

A

Size

46 x 46 mm

Artwork Notes

3mm corner radius; 2mm safe margin; white to be 

printed shown in 50% process magenta

Revision Changes

This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for 
outside parties without the explicit consent of Champion Power Equipment.

Fuel

C

  

WARNING

DO NOT TOUCH! 

DO NOT use exhaust or muffler 

extensions, in doing so your 

warranty will be voided.

Operation of this equipment may create sparks that can start fires around dry vegetation. A spark 
arrestor may be required. The operator should contact local fire agencies for laws and regulations 
relating to fire prevention requirements. If installed, clean every 100 hours or every season.

 

10

57

-B

Y-L

-A

Colors

LPN

Rev

Size

252 x 26 mm

Artwork Notes

3mm corner radius; 2mm safe margin; to be printed 

on white substrate

Revision Changes

---

This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for 
outside parties without the explicit consent of Champion Power Equipment.

K

185

165

123

---

1057-BY-L

A

Hot Surface

D

IP Grade

SERIAL NO.

MODEL

500560-UK

XXXXXXXXXXXX

XXXX

IP23M

Year of Manufacture

CHAMPION POWER EQUIPMENT, INC.

12039 SMITH AVENUE

SANTA FE SPRINGS, CA 90670

USA / É.-U.

MADE IN CHINA

Low Power Generating Set

K

---

---

---

---

Colors

APN

Rev

Size

123 x 40 mm

Artwork Notes

3mm corner radius; 2mm safe margin; to be printed 

on 

WHITE substrate.

Revision Changes

This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for 
outside parties without the explicit consent of Champion Power Equipment.

AC AMPS

Performance Class

FREQUENCY (Hz)

RPM

PHASE

POWER FACTOR

23.3A/11.7A

G1

50

3000

1

1.0

120V/240V

QUALITY CLASS

NET WEIGHT

INSULATION CLASS

MAX AMBIENT TEMP

RATED OUTPUT

RATED VOLTAGE

MAX POWER

A

46kg

H

COP:2.8kW

3.2kW S2 5min

104°F/40°C

Dataplate

Top

A

b

Back

Side

C

D

Summary of Contents for 500560-UK












































Reviews: