background image

17

  

REV 46551-20130402

ENGLISH

 

46551

Oil

Use 10W-30 automotive oil.
Oil capacity is 0.63 qt (0.6 L).
DO NOT OVERFILL.
Please reference the following chart for recommended 
oil types for use in the generator.

fuel

Fuel capacity is 4.0 gallons (15 L). Use regular unleaded 
gasoline with a minimum octane rating of 85 and an 
ethanol content of less than 10% by volume.

Generator Specifications

 

– Model

46551

 

– Rated Wattage

3000 Watts

 

– Starting Wattage

4000 Watts

 

– AC Voltage

120 V

 

– Phase

Single

 

– Frequency

60 Hz

 

– Fuel Capacity

4.0 gallons (15 L)

 

– Gross Weight

116.8 lbs. (53 kg)

 

– Net Weight

108 lbs. (49 kg)

 

– Height

20.3 inches (51.5 cm)

 

– Width

23.2 inches (59 cm)

 

– Length

30.2 inches (76.8 cm)

SPECIfICATIONS

Engine Specifications

 

– Model

YF168FD-2-01

 

– Displacement

196cc

 

– Type

4-Stroke OHV

 

– Start Type

Recoil

Maintenance Valve Clearance

 

– Intake: 0.13 – 0.17 mm (0.005 – 0.007 in.)

 

– Exhaust: 0.18 – 0.22 mm (0.007 – 0.009 in.)
Note: Tech bulletin regarding the valve adjustment 
procedure is on www.championpowerequipment.com.

Spark Plugs

OEM spark plug: NHSP F6RTC
Replacement spark plug: NGK BPR6ES or equivalent
Make certain the spark plug gap is 0.7 - 0.8 mm or 
(0.028 - 0.031 in.).

An Important Message About Temperature

Your Champion Power Equipment product is designed 
and rated for continuous operation at ambient 
temperatures up to 40°C (104°F). When your product is 
needed your product may be operated at temperatures 
ranging from -15°C (5°F) to 50°C (122°F) for short 
periods. If the product is exposed to temperatures 
outside this range during storage, it should be brought 
back within this range before operation. In any event, 
the product must always be operated outdoors, in a  
well-ventilated area and away from doors, windows and 
other vents.

Summary of Contents for 46551































Reviews: