manualshive.com logo in svg

Champion 2000 Series, Installation & Operation Manual, Page: 15 / 44

Share
Download
Champion 2000 Series Installation & Operation Manual Download Page 15

7

Installation

NOTE:

Consult a qualified chemical supplier for chemical 

supplies and chemical dispensing equipment.

Chemical Dispenser Provisions

Detergent

Rinse-aid

Vent Fan Control  

1.  A vent fan control signal is provided on a terminal block located 

inside the top-mounted control cabinet.  The terminal locations 

are clearly marked.

2.  The 120VAC signal is designed only to operate an external vent  

fan contactor (supplied by others)  and is limited to 1 AMP 

maximum load and is available when the dishwasher power 

switch is turned ON.

CAUTION:

Do not connect a vent fan motor to the signal connection terminals.

SIGNAL ONLY

VENT FAN

COMMON

COMMON

120V

DETERGENT

120V

RINSE AID

120V

The Vent Fan Control Signal is limited to 

120VAC 1 Amp maximum load.

Provisions for chemical suppliers to connect their 

chemical dispensing systems are provided on the 

dishwasher and include: 

      

1.  A 1/4" NPT plastic fitting as a rinse-aid injection 

point.  The fitting is installed in the upper final  

rinse piping located at the top-rear of the 

dishwasher (see illustration at left). 

2.  Two 7/8" holes are provided on the right-side 

rear of the wash tank as detergent injection 

points.

3.  Detergent and rinse-aid control signals are 

available inside the top-mounted control 

cabinet.  The signals are 120VAC, Max. 1 Amp 

load.  Connection points are located on a  

labeled terminal block (see below).

4.  DO NOT REMOVE THE JUMPER BETWEEN 

THE COMMON TERMINALS.

Detergent and Rinse-aid Injection Points

SIGNAL ONLY

VENT FAN

COMMON

COMMON

120V

DETERGENT

120V

RINSE AID

120V

JUMPER

DO NOT REMOVE THE JUMPER 

BETWEEN THE COMMON TERMINALS

Summary of Contents for 2000 Series













































Reviews:

No comments