background image

  

4

100215

 

ENGLISH

SAFETy RULES

Improper treatment or use of the generator can 
damage it, shorten its life and void your warranty.

Use the generator only for intended uses.
Operate only on level surfaces.
DO NOT expose generator to excessive moisture, 
dust, or dirt.
DO NOT allow any material to block the cooling slots.
If connected devices overheat, turn them off and 
disconnect them from the generator.
DO NOT use the generator if:

 

– Electrical output is lost

 

– Equipment sparks, smokes or emits flames

 

– Equipment vibrates excessively

CAUTION

Operation of this equipment may create sparks that 

can start fires around dry vegetation.

A spark arrestor may be required. The operator 

should contact local fire agencies for laws or 

regulations relating to fire prevention requirements.

WARNING

Rapid retraction of the starter cord will pull hand and 
arm towards the engine faster than you can let go. 
Unintentional startup can result in entanglement, 
traumatic amputation or laceration.  
Broken bones, fractures, bruises or sprains could result.

When starting engine, pull the starter cord slowly 
until resistance is felt and then pull rapidly to avoid 
kickback.
DO NOT start or stop the engine with electrical 
devices plugged in.

WARNING

LIQUID PETROLEUM GAS (LPG) IS HIGHLY 
FLAMMABLE AND EXPLOSIVE. 
 
Fire or explosion can cause severe burns or death.  
Unintentional startup can result in entanglement, 
traumatic amputation or laceration. 

Liquefied Petroleum Gas (LPG):

 

– LPG IS HIGHLY FLAMMABLE AND EXPLOSIVE.

 

– Flammable gas under pressure can cause a fire 

or explosion if ignited.

 

– LPG is heavier than air and can settle in low 

places while dissipating.

 

– LPG has a distinctive odor added to help detect 

potential leaks quickly.

 

– In any petroleum gas fire, flames should not be 

extinguished unless by doing so the fuel supply 
valve can be turned OFF. This is because if a 
fire is extinguished and a supply of fuel is not 
turned OFF, then an explosion hazard could be 
created.

 

– When exchanging LPG cylinders, be sure the 

cylinder valve is of the same type.

 

– Always keep the LPG cylinder in an upright 

position.

When starting the generator:

DO NOT attempt to start a damaged generator. 
Make certain that the gas supply, air filter, spark 
plug, fuel lines and exhaust system are properly in 
place.
Make certain that the generator is resting firmly on 
level ground.

When operating the generator:

DO NOT move or tip the generator during operation.
DO NOT tip the generator or allow oil to spill.

When transporting or servicing the generator:

Make certain that the fuel shutoff valve is in the off 
position and the LPG cylinder is not attached.
Disconnect the spark plug wire.

When storing the generator:

Store away from sparks, open flames, pilot lights, 
heat and other sources of ignition.

DANGER

Exceeding the generator’s running capacity can 
damage the generator and/or electrical devices 
connected to it.

DO NOT overload the generator.
Start the generator and allow the engine to stabilize 
before connecting electrical loads.
Connect electrical equipment in the off position, 
and then turn them on for operation.
Turn electrical equipment off and disconnect before 
stopping the generator.
DO NOT tamper with the governed speed. 
DO NOT modify the generator in any way.

CAUTION

Summary of Contents for 100215































Reviews: