background image

5

90720 - 7 TON FULL BEAM LOG SPLITTER

IMPORTANT SAFETY INSTRUCTIONS

 

WARNING

Before removing the pin installed into the front support leg 
make sure hitch is installed onto vehicle. Releasing the pin 
before will cause support leg to slide up and possibly cause 
injury.

 

WARNING

Skin Injection Hazard. High pressure hydraulic oil can inject 
under your skin.

Make sure all fittings are tightly secure before applying 
pressure. Relieve system of pressure before servicing.

 

WARNING

Rapid retraction of the starter cord will pull hand and arm 
towards the engine faster than you can let go. Unintentional 
startup can result in entanglement, traumatic amputation or 
laceration. Broken bones, fractures, bruises or sprains could 
result.

When starting engine, pull the starter cord slowly until 
resistance is felt and then pull rapidly to avoid kickback.

 

CAUTION

Parts of the hydraulic circuit (cylinder, pump, valve-body, 
hoses) can become very hot during operation.

 

WARNING

In most states towing on public streets is either prohibited or 
would require further licensing or modifications. Please check 
with your local authorities or DMV regarding regulations, 
restrictions and registration.

 

CAUTION

Improper treatment or use of the log splitter can damage it, 
shorten its life and void your warranty.

Use the log splitter only for intended uses.

Operate only on level surfaces.

DO NOT expose log splitter to excessive moisture, dust, 
or dirt.

DO NOT allow any material to block the cooling slots.

DO NOT use the engine if:

 

Equipment sparks, smokes or emits flames

 

Equipment vibrates excessively

Fuel Safety

 

DANGER

GaSOLINE aND GaSOLINE VaPORS aRE hIGhLY 
FLammaBLE aND EXPLOSIVE.

Fire or explosion can cause severe burns or death.

Gasoline and gasoline vapors:

 

Gasoline is highly flammable and explosive.

 

Gasoline can cause a fire or explosion if ignited.

 

Gasoline is a liquid fuel but its vapors can ignite.

 

Gasoline is a skin irritant and needs to be cleaned up 
immediately if spilled on skin or clothes.

 

Gasoline has a distinctive odor, this will help detect potential 
leaks quickly.

 

In any petroleum gas fire, flames should not be extinguished 
unless by doing so the fuel supply valve can be turned OFF. 
This is because if a fire is extinguished and a supply of fuel is 
not turned OFF, then an explosion hazard could be created.

 

Gasoline expands or contracts with ambient temperatures. 
Never fill the gasoline tank to full capacity, as gasoline needs 
room to expand if temperatures rise.

When adding or removing gasoline:

Turn the engine off and let it cool for at least two minutes before 
removing the gasoline cap. Loosen the cap slowly to relieve 
pressure in the tank.

Only fill or drain gasoline outdoors in a well-ventilated area.

DO NOT pump gasoline directly into the engine at the gas station. 
Use an approved container to transfer the fuel to the engine.

DO NOT overfill the gasoline tank.

Always keep gasoline away from sparks, open flames, pilot lights, 
heat and other sources of ignition.

DO NOT light or smoke cigarettes.

When starting the engine:

DO NOT attempt to start a damaged engine. 

Make certain that the gasoline cap, air filter, spark plug, fuel lines 
and exhaust system are properly in place.

Allow spilled gasoline to evaporate fully before attempting to start 
the engine.

Make certain that the log splitter is resting firmly on level ground.

When operating the log splitter:

DO NOT move or tip the log splitter during operation.

DO NOT tip the log splitter or allow fuel or oil to spill.

Summary of Contents for 90720





































Reviews: