background image

 

© 2008, The Chamberlain Group, Inc.

114A3619 

All Rights Reserved 

CHAMBERLAIN

®

 SERVICE IS 

ON CALL

OUR LARGE SERVICE ORGANIZATION

 SPANS AMERICA

INSTALLATION AND SERVICE INFORMATION 

IS AS NEAR AS YOUR TELEPHONE. 

SIMPLY DIAL OUR TOLL FREE NUMBER:

1-800-528-9131

www.chamberlain-diy.com

For professional installation, parts and service, 

contact 

your local CHAMBERLAIN

®

 dealer. Look for him in the Yellow 

Pages, or call our Service number for a list of dealers in your 
area.

HOW TO ORDER

REPAIR PARTS

Selling prices will be furnished on request, or parts will be 
shipped at prevailing prices and you will be billed accordingly.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE 

FOLLOWING INFORMATION:

  • 

 

PART NUMBER

  • 

PART 

NAME

  • 

MODEL 

NUMBER

ADDRESS ORDERS TO:

THE CHAMBERLAIN GROUP, INC.

Technical Support Group

6050 S. Country Club Road

Tucson, Arizona 85706

SERVICE INFORMATION

TOLL FREE NUMBER:

1-800-528-9131

CHAMBERLAIN

®

 THREE YEAR LIMITED WARRANTY

10 YEAR BELT LIMITED WARRANTY & LIFETIME MOTOR LIMITED WARRANTY

The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally 
installed, that it is free from defect in materials and/or workmanship for a period of three years from the date of purchase, [and that the belt is 
free from defect in materials and/or workmanship for a period of 10 years from the date of purchase and that the motor is free from defect in 
materials and/or workmanship for the lifetime of the product]. The proper operation of this product is dependent on your compliance with the 
instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this limited 
warranty in its entirety.

If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-9131, toll free, 
before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair. You will be advised of 
shipping instructions when you call. Please include a brief description of the problem and a dated proof-of-purchase receipt with any product 
returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective and 
covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returned pre-paid. Defective parts will 
be repaired or replaced with new or factory-rebuilt parts at Seller’s sole option.

ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY 
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE THREE YEAR LIMITED WARRANTY PERIOD SET 
FORTH ABOVE [EXCEPT THE IMPLIED WARRANTIES WITH RESPECT TO THE BELT AND MOTOR, WHICH ARE LIMITED IN DURATION 
TO 10 YEARS FOR THE BELT AND THE LIFETIME LIMITED WARRANTY PERIOD FOR THE MOTOR], AND NO IMPLIED WARRANTIES 
WILL EXIST OR APPLY AFTER SUCH PERIOD.  Some States do not allow limitations on how long an implied warranty lasts, so the 
above limitation may not apply to you. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY 
IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE 
REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR 
CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT OF BATTERIES AND LIGHT BULBS OR UNITS 
INSTALLED FOR NON-RESIDENTIAL USE.

THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR 
HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. THIS 
LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. ANY SERVICE CALL THAT 
DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU. 

UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN 
CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF 
WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED 
HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS 
PRODUCT. 

Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not 

Summary of Contents for Whisper Drive Security+ HD700DS









































Reviews: