background image

Lens

Guide

Lens

Tab

Lens

Slot

75 Watt

(Maximum)

Light Bulb

The Chamberlain Group, Inc.
STEP 7 Install Lights and Lenses - CGI
10/7/91 - 5/2/92 - 5/26/92

Lens Slot

75 Watt Max.

Light Bulb

Lens Tab

Light
Lens

Panel Screw

Install the lights

• Install a 75 watt maximum light bulb in each

socket. The lights will turn ON and remain lit for
approximately 4-1/2 minutes when power is
connected. Then the lights will turn OFF.

• If the bulbs burn out prematurely due to vibration,

replace with "Garage Door Opener" bulbs.

Install the lenses 

The Force Adjustment Control and Smart Button are
located on the back panel.

For convenience, you may wish to install the lens
after installation and adjustment procedures are
completed.

• Slide each lens into guides. Snap bottom tabs into

lens slots. 

• Reverse the procedure to remove the lenses.

Installation Step 7

Install the Light and the Lenses

Installation Step 8

Attach the Manual Release
Rope and Handle

Do not use the red handle to pull the door
open or closed.

The rope knot could become

untied and you could fall. Use the manual
release only to disengage the trolley and, if
possible, only when the door is closed.

Garage doors are heavy. If the door is open
when the handle is pulled, the door could
close inadvertently if it is not properly
balanced. Serious injury may result to persons
under the door. Make sure the doorway is clear
of persons and obstructions before pulling
handle when door is open.

• Thread one end of the rope through the hole in the

top of the red handle so "NOTICE" reads right side
up as shown. Secure with an overhand knot.

The knot should be at least 1" from the end of the
rope to prevent slipping.

• Thread the other end of the rope through the hole in

the release arm of the outer trolley.

• Adjust rope length so the handle is 6 feet above the

floor. Secure with an overhand knot.

If it is necessary to cut the rope, heat seal the cut
end with a match or lighter to prevent unraveling.

Trolley

Step 5 Attach Emergency Release Rope & Handle - SEARS 315-699 (Yellow Disk #2)

Models 53315, 53415, 53515, 53625 & 53699

6/20/89 - 6/27/89

NOTICE

Overhand

Knot

Manual

Release Handle

Rope

Overhand

Knot

Trolley

Release Arm

19

WARNING

CAUTION

WARNING

Summary of Contents for Security+ 6200









































Reviews: