Chamberlain Security+ 1245GMR-1/3HP Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 36

background image

21

Header Wall

Vertical
Centerline of
Garage Door

Finished Ceiling

Optional
Placement
of Door
Bracket

Header

Bracket

Door
Bracket

2x4 Support

For a door with no exposed framing,
or for the optional installation, use
5/16"x1-1/2" lag screws (not provided)
to fasten door bracket.

METAL DOOR

Top of Door
(Inside
Garage)

Door
Bracket

Optional
Placement

Top Edge
of Door

1/4"-14x5/8"
Self-Threading
Screw

Door
Bracket

Top of Door
(Inside
Garage)

Carriage Bolt
5/16"x2"
(Not provided)

Optional
Placement

Lock
Washer
5/16"

Nut

5/16"-18

Top Edge
of Door

WOOD DOOR

HORIZONTAL AND VERTICAL
REINFORCEMENT IS NEEDED

FOR LIGHTWEIGHT GARAGE
DOORS (FIBERGLASS,
ALUMINUM, STEEL, DOORS
WITH GLASS PANEL, ETC).
(NOT PROVIDED)

ONE-PIECE DOORS

Please read and comply with the warnings and
reinforcement instructions on the previous page.
They apply to one-piece doors also.

• Center the door bracket on the top of the door, in

line with the header bracket as shown. Mark either
the left and right, or the top and bottom holes.

•

Metal Doors: Drill 3/16" pilot holes and fasten the
bracket with the 1/4"-14x5/8" self-threading screws
provided.

•

Wood Doors: Drill 5/16" holes and use 5/16"x2"
carriage bolts, lock washers and nuts (not
provided) or 5/16"x1-1/2" lag screws (not provided)
depending on your installation needs.

NOTE: The door bracket may be installed on the top
edge of the door if required for your installation.
(Refer to the dotted line optional placement drawing.)

Self-Threading
Screw
1/4"-14x5/8"

HARDWARE SHOWN

ACTUAL SIZE

«
...
19
20
21
22
23
...
»

Summary of Contents for Security+ 1245GMR-1/3HP





































Reviews:

No comments

Related manuals for Security+ 1245GMR-1/3HP

Brand: Genius Pages: 22

Brand: RAMSET Pages: 26

Brand: Nice Pages: 112

SensingEdge MT22

Brand: Miller Edge Pages: 2

Brand: cedamatic Pages: 8

Brand: cedamatic Pages: 15

Brand: cedamatic Pages: 24

Brand: tau Pages: 76

Brand: DACE Pages: 22

Brand: FAAC Pages: 45

Brand: Garaga Pages: 2

Brand: Accessmatic Pages: 78

Brand: vds Pages: 13

Brand: CAME Pages: 32

FROG PLUS Series

Brand: CAME Pages: 18

Brand: Coline Pages: 5

STYLO 8K01MB-0574

Brand: CAME Pages: 12

Brand: tau Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands