background image

21

INSTALLATION STEP 8

Install the Lights 

•  

Press the release tabs on both sides of lens. Gently 
rotate lens back and downward until the lens hinge is 
in the fully open position. Do not remove the lens.

•  

Install a 100 watt maximum light bulb in each socket. 
Light bulb size should be A19, standard neck only. The 
lights will turn ON and remain lit for approximately 
4-1/2 minutes when power is connected. Then the 
lights will turn OFF.

•  

Reverse the procedure to close the lens.

•  

Use A19, standard neck garage door opener bulbs for 
replacement.

NOTE:

 

Use only standard light bulbs. The use of short 

neck or speciality light bulbs may overheat the endpanel 
or light socket.

INSTALLATION STEP 9

Attach the Emergency Release Rope 
and Handle

•  

Thread one end of the rope through the hole in the top 
of the red handle so “NOTICE” reads right side up as 
shown. Secure with an overhand knot at least 
1" (2.5 cm) from the end of the rope to prevent 
slipping.

•  

Thread the other end of the rope through the hole in 
the release arm of the outer trolley.

•  

Adjust rope length so the handle is 6 feet (1.83 m) 
above the floor. Ensure that the rope and handle clear 
the tops of all vehicles to avoid entanglement. Secure 
with an overhand knot.

NOTE: 

If it is necessary to cut the rope, heat seal the cut 

end with a match or lighter to prevent unraveling.

To prevent possible SERIOUS INJURY or DEATH from a 
falling garage door:
•  If possible, use emergency release handle to disengage 

trolley ONLY when garage door is CLOSED. Weak or 
broken springs or unbalanced door could result in an open 
door falling rapidly and/or unexpectedly.

•  NEVER use emergency release handle unless garage 

doorway is clear of persons and obstructions.

•  NEVER use handle to pull door open or closed. If rope knot 

becomes untied, you could fall.

Lens
Hinge

100 Watt (Max)
Standard Light Bulb

Release Tab

100 Watt (Max)
Standard Light Bulb

To prevent possible OVERHEATING of the endpanel or light 
socket:
•   DO NOT use short neck or specialty light bulbs.
•   DO NOT use halogen bulbs. Use ONLY incandescent.
To prevent damage to the opener:
•   DO NOT use bulbs larger than 100W.
•  ONLY use A19 size bulbs.

Trolley Release Arm

NOTICE 

Overhand
Knot

Emergency

Release Handle

Trolley

Summary of Contents for Power Drive PD432DM









































Reviews: