background image

The Chamberlain Group, Inc.

845 Larch Avenue

Elmhurst, Illinois 60126-1196

www.chamberlain.com

CONTENTS

Preparation .............................. 1-4

Assembly ................................. 5-9

Installation ............................ 10-17

Install the Door Control ............. 18-19

Install the Protector System

®

 ...... 20-23

Power  .................................. 24-25

Adjustments .......................... 26-28

Operation.................................. 29

Features ................................... 30

Remote Control .......................... 31

To Erase the Memory .................... 32

To Open the Door Manually ............ 32

Maintenance .............................. 33

Diagnostic Chart ......................... 34

Warranty .................................. 35

Chain Drive
Garage Door Opener

■ 

 Please read this manual and the enclosed safety materials carefully!

  Fasten the manual near the garage door after installation.

■ 

  The door WILL NOT CLOSE unless the Protector System

®

 is connected and 

properly aligned.

  Periodic checks of the garage door opener are required to ensure safe operation.

  The model number label is located on the back panel of your garage door opener.

  This garage door opener is compatible with S 2.0

®

 accessories.

   WARNING: To reduce the risk of injury to persons – Use this opener ONLY with a 

7 foot sectional door.

Serial Number:

Date of Purchase:

 

Model Number: 

Model PD220

FOR RESIDENTIAL USE ONLY 

INSTALL ON 7 FOOT 
SECTIONAL DOORS ONLY

Register your new garage door opener at 
www.prodregister.com/chamberlain or 
scan the QR code with your smartphone

Write down the following information 
for future reference:

Summary of Contents for PD220





















Reviews: