background image

Carton Inventory

Overview

The Intercom has up to a 1000' range and allows
multiple simultaneous conversations, using a 
900 Mhz secure digital radio link. The intercoms form
an exclusive network and respond only to other
intercoms in the network.

Intercom (2 in Model LSIS)

1

Rubber Pads 

(2 in Model LSIS)

Operation & Features

Channel Select Button:

Press the

Channel Select button to set
intercom to one of four secure
channels or the paging channel.
The default channel for the
intercom is the paging channel
where all four channel lights are lit. An intercom on a
channel can only hear an intercom on the same
channel or on the paging channel.

Battery:

The AA Alkaline batteries (not provided) will

last up to a year depending on use (Lithium batteries
recommended for colder
environments). When batteries are
low intercom will emit two beeps
every ten minutes.
An AC Adapter (not provided) can
also be used to power the intercom.
In this case, both the power and
channel lights will remain on.

Conference Mode:

Conference Mode allows multiple

intercoms to participate in a conversation compared
to Normal Mode in which only two intercoms can
communicate. All intercoms must be set to the same
channel or the paging channel to be in
Conference Mode. To put intercom in
Conference Mode set Dipswitch #2 to UP
position.

Monitor Mode:

Monitor Mode is

used to monitor the noise in a
specific room. Place the intercom in
the room that is to be monitored
and press the Monitor button until a
tone is heard. The Active Light will
be lit while the intercom is in Monitor
Mode. Any other networked intercom can listen to
that room. If a specific channel is selected for Monitor
Mode then only other intercoms on that channel or on
the paging channel can listen. Press the Monitor
button again to exit Monitor Mode. A tone will be
heard indicating Monitor Mode is no longer active.

Voice Activation Mode (VOX):

Voice Activation

Mode (VOX) allows a call to be answered without
pressing the Talk button. Once a call is heard on an
intercom which has been set to VOX, a response can
be given by speaking loudly into the intercom. There
will be a slight delay when VOX is first activated by a
voice, but will continue to transmit audio until
the speaking stops. To put intercom into VOX,
place Dipswitch #1 to the UP position.

On/Off:

To turn intercom ON, press Talk button.To

turn intercom OFF, hold down the Volume DOWN
button for 5 seconds.

Talk Button:

To talk, hold down the

Talk button. All intercoms in the
network that are on the same
channel will receive the signal.
Release the Talk button when done
talking and within 10-15 seconds
press and hold the Talk button of a different intercom
to make a secure channel between the two. Once the
channel is made the other intercoms in the network
cannot hear the conversation.

Volume:

Pressing the Volume DOWN button will

lower the volume and pressing the Volume UP button
will increase the volume.

Volume UP
Button

Talk Button

Learn Button

Dipswitch #1
Dipswitch #2

AC Adapter

Model LSIA & LSIS

Wireless Portable Intercom - Extreme Range

®

OPTIONAL

1

2

1

2

Channel
Select
Button

Channel Lights

Power Light

Active Light

Volume DOWN 
Button

Monitor Button

Speaker

Summary of Contents for LSIA

Page 1: ...eard The Active Light will be lit while the intercom is in Monitor Mode Any other networked intercom can listen to that room If a specific channel is selected for Monitor Mode then only other intercoms on that channel or on the paging channel can listen Press the Monitor button again to exit Monitor Mode A tone will be heard indicating Monitor Mode is no longer active Voice Activation Mode VOX Voi...

Page 2: ...earn button on the new intercom until a beep is heard Within 10 seconds put any networked intercom into Learn Mode refer to table below Press and release the Talk button to verify network is complete INTERCOM LEARN MODE Press the Learn button until a beep is heard Press and hold both buttons for 5 seconds OR Each intercom will emit a tone when programmed into network Repeat for any additional inte...

Page 3: ...olarity on the round plug Need to clear intercom s memory Press and hold Learn button an initial beep will be heard Continue to hold until a second beep is heard about 15 seconds Ensure other intercoms are not activated during this time Intercoms in the network that are on will signal during the clearing process Once memory is clear the intercom can be programmed to a new network Static and feedba...

Page 4: ...ing or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to Comply with FCC Standards FOR HOME OR OFFICE USE Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER 1 800 ...

Reviews: