background image

 

© 2008, The Chamberlain Group, Inc.

114A3645 

All Rights Reserved 

LIFTMASTER

®

 ONE-YEAR LIMITED WARRANTY

FOUR YEAR MOTOR LIMITED WARRANTY

The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is 
originally installed, that it is free from defect in materials and/or workmanship for a period of one year from the date of purchase and that 
the motor is free from defect in materials and/or workmanship for a period of four years from the date of purchase. The proper operation 
of this product is dependent on your compliance with the instructions regarding installation, operation, maintenance and testing. Failure 
to comply strictly with those instructions will void this warranty in its entirety.

If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 
1-800-528-9131, toll free, before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty 
repair. You will be advised of shipping instructions when you call. Please include a brief description of the problem and a dated proof-of-
purchase receipt with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by 
Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost 
to you and returned pre-paid. Defective parts will be repaired or replaced with new or factory-rebuilt parts at Seller’s sole option.

THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED 
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, AND OF ANY OTHER 
OBLIGATIONS OR LIABILITY ON SELLER’S PART. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, 
DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, 
FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO 
THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT OF BATTERIES 
AND LIGHT BULBS OR UNITS INSTALLED FOR NON-RESIDENTIAL USE.

THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE 
DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. 
ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A 
FEE TO YOU. 

UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES 
ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR 
BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT 
COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE 
SALE OF THIS PRODUCT.

 

Some provinces do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or 
exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from 
province to province.

LIFTMASTER

®

 SERVICE IS 

ON CALL

OUR LARGE SERVICE ORGANIZATION

 SPANS AMERICA AND CANADA

INSTALLATION AND SERVICE INFORMATION IS AS NEAR 

AS YOUR TELEPHONE.

SIMPLY DIAL OUR TOLL FREE NUMBER:

1-800-528-9131

 

www.liftmaster.com

For professional installation, parts and service, 

contact 

your local LIFTMASTER/CHAMBERLAIN dealer. Look for him 

in the Yellow Pages, or call our Service number for a list of 

dealers in your area.

HOW TO  ORDER

REPAIR PARTS

Selling prices will be furnished on request or parts will be 

shipped at prevailing prices and you will be billed accordingly.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE 

FOLLOWING INFORMATION:

  • 

 

PART NUMBER

  • 

PART 

NAME

  • 

MODEL 

NUMBER

ADDRESS ORDERS TO:

THE CHAMBERLAIN GROUP, INC.

Technical Support Group

6050 S. Country Club Road

Tucson, Arizona 85706

SERVICE INFORMATION

TOLL FREE NUMBER:

1-800-528-9131

Summary of Contents for LiftMaster Professional Security+ 3245M









































































Reviews: