114A2910B-GB
9-GB
Program your Keyless Entry
Activate the opener only when door is in full view,
free of obstruction and properly adjusted. No one
should enter or leave garage while door is in
motion. Do not allow children to operate push
button(s) or remote(s). Do not allow children to
play near the door.
NOTE: Your new Keyless Entry must be programmed
to operate your garage door opener.
Program the Receiver to Match Additional Remote
Control Code
Using the orange “LEARN” Button:
1. Press and release the orange “learn” button (1) on
opener. The learn indicator light will glow steadily
for 30 seconds.
2. Within 30 seconds, enter a four digit personal
identification number (PIN) of your choice on the
keypad (2), then press and hold the ENTER
button.
3. Release the button when the opener light blinks
(3). It has learned the code. If the light bulb is not
installed, two clicks will be heard.
Using the Multi-Function Door Control:
NOTE: This method requires two people if the
Keyless Entry is already mounted outside the garage.
4. Enter a four digit personal identification number
(PIN) of your choice on the keypad, then press
and hold ENTER.
5. While holding the ENTER button, press and hold
the LIGHT button on the Multi-Function Door
Control.
6. Continue holding the ENTER and LIGHT buttons
while you press the push bar on the Multi-Function
Door Control (all three buttons are held).
7. Release buttons when the opener light blinks. It
has learned the code. If the light bulb is not
installed, two clicks will be heard.
1
2
3
4
7
LOCK
LIGHT
5
LOCK
LIGHT
6
LOCK
LIGHT
1
3
2
60 s
120 s
180 s
O
–
24
Using the Wall-Mounted Door Control
THE MULTI-FUNCTION DOOR CONTROL
Press the push bar (1) to open or close the door.
Press again to stop the door.
Light feature
Press the light button to turn the opener light on or off.
It will not control the opener lights when the door is in
motion. If you turn it on and then activate the opener,
the light will remain on for 2 1/2 minutes. Press again
to turn it off sooner. The 2 1/2 minute interval can be
changed to 1-1/2, 3-1/2 or 4-1/2 minutes as follows:
Press and hold the Lock button until the light
blinks(about 10 seconds). A single blink indicates that
the timer is reset to 1-1/2 minutes. Repeat the
procedure and the light will blink twice, resetting the
timer to 2-1/2 minutes. Repeat again for 3-1/2 minute
interval, etc., up to a maximum of four blinks and
4-1/2 minutes.
Lock feature
Designed to prevent operation of the door from hand-
held remote controls. However, the door will open and
close from the Door Control, the Outside Keylock and
the Keyless Entry Accessories.
To activate, press and hold the Lock button (3) for 2
seconds. The push bar light will flash as long as the
Lock feature is on.
To turn off, press and hold the Lock button again for
2 seconds. The push bar light will stop flashing. The
Lock feature will also turn off whenever the “LEARN”
button on the opener panel is activated.
25
1
LOCK
LIGHT
2
114A2910B-GB
10-GB
Setting the Limits
Travel limits regulate the points at which the door
will stop when moving up or down. Follow the
steps below to set the limits.
To program the travel limits:
1. Press and hold the black button (1) until the yellow
indicator light (3) starts flashing slowly and then
release.
2. Push and hold the black button (1) until the door
reaches the desired open position. Adjust the
position of the door by using the black (1) and
orange (2) buttons. Black moves the door UP,
orange moves the door DOWN.
3. Push the programmed remote control (4) or push
bar on the door control that was shipped with your
opener. This sets the full UP (open) position. The
door will travel to the floor and reverse back to the
UP (open) position. The opener has learned its
travel limits.
Check to be sure the door is high enough for your
vehicle. Adjust if necessary.
4. The indicator light (3) will stop flashing when the
limits have been learned.
NOTE: If the door reverses before it reaches the floor
proceed to #15 of the Having a Problem? section and
follow the instructions for setting the limits manually.
The force MUST be learned in order to properly
complete the setting of the limits.
4
1
2
3
LiftM
ast
er
LiftMaste
r
2
3
1
1
3
2
60 s
120 s
180 s
O
–
26
ADJUSTMENT SECTION
Setting the Force
The force, as measured on the closing edge of the
door, should not exceed 400N (40kg). If the
closing force is measured to more than 400N, the
Protector System must be installed See step 29.
The force setting regulates the amount of power
required to open and close the door.
1. Locate the orange button (2).
2. Push the orange button (2) twice to enter unit into
Force Adjustment Mode. The LED (3) (indicator
light) will flash quickly.
3. Push the programmed remote control (4) or push
bar on the door control that was shipped with your
opener. The door will travel to the DOWN (close)
position. Push the remote control (4) again, the
door will travel to the UP (open) position.
The LED (3) (indicator light) will stop flashing when
the force has been learned.
The door must travel through a complete cycle, UP
and DOWN, in order for the force to be set properly. If
the unit cannot open and close your door fully, inspect
your door to insure that it is balanced properly and is
not sticking or binding.
(2x)
4
LiftM
ast
er
LiftMaste
r
3
2
2
3
1
3
2
60 s
120 s
180 s
O
–
27
Test the Safety Reverse System
The safety reverse system test is important.
Garage door must reverse on contact with a
40mm obstacle laid flat on the floor. Failure to
properly adjust opener may result in serious
personal injury from a closing garage door.
Repeat test once a month and adjust as needed.
Procedure: Place a 40mm obstacle (1) laid flat on the
floor under the garage door. Operate the door in the
down direction. The door must reverse on the
obstruction. If the door stops on the obstruction,
remove obstruction and repeat Setting the Limits step
26. Repeat test.
When the door reverses on the 40mm obstacle,
remove the obstruction and run the opener through a
complete travel cycle. Door must not reverse in
closed position. If it does, repeat Setting the Limits
and Force steps 26 and 27 and repeat safety reverse
test.
Place 20kg at the center of the door and ensure that
the door will not move up more than 500mm.
1
28
