Chamberlain CA1000 User Manual Download Page 5

5

To reduce the risk SEVERE INJURY or PROPERTY DAMAGE:
•  Attach jumper cables to a battery and vehicle chassis as indicated below. Jump 

Starter is intended for a NEGATIVELY GROUNDED vehicle.  

•  DO NOT touch the red and black jumper clamps together. 
•  Keep jumper cables away from moving engine parts. 
•  Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to 

persons. 

•  Check polarity of battery posts. Positive is red, and negative is black.
•  ONLY connect red (POSITIVE) clamp from jump starter to POSITIVE post of the 

car battery (POS, P, +, RED) and the black (NEGATIVE) clamp from jump starter 
to NEGATIVE post of the car battery (NEG, N, -, BLACK). DO NOT connect 
jumper clamp to carburetor, fuel lines, or sheet-metal body parts.

•  After the vehicle has started, disconnect the jumper cables from the Jump 

Starter prior to removing the jumper clamps from the battery posts. 

•  DO NOT attempt to jump start your vehicle more than three consecutive times.  

If the vehicle will not start after three attempts, consult a mechanic.

JUMPSTARTING A VEHICLE

1.  Slide the On/Off switch to the ‘On’ position.  Check the charge level displayed on 

the LCD display. The minimum charge required to jump start a vehicle is 40%. It 
is not necessary to have the switch in the “On” position to jump start a vehicle.

2.   Connect the red jumper clamp to the positive (+) terminal on the car battery.
3.   Connect the black jumper cable clamp to the negative (-) terminal on the car 

battery. 

4.  Connect the battery clamp assembly plug to the 12V Jump Starter.
5.  Start the vehicle.  If the vehicle does not start within few seconds, turn the key off 

and wait a minute before attempting to start the vehicle again. 

NOTE:

 DO NOT attempt to jump start your vehicle more than three consecutive 

times. If the vehicle will not start after three attempts, consult a mechanic.

1.  Once the vehicle is running, disconnect the jumper cables from the Jump Starter.
2.  Remove the jumper clamps from the vehicle’s positive and negative terminals.
3.  Slide the On/Off switch to the ‘Off’ position if it is ON.
4.  Be sure to recharge the Jumper Starter prior to using it again.

1

2

3

Summary of Contents for CA1000









Reviews: