Chamberlain C2212T Installation Manual Download | Manualshive

Page: 37 / 52

background image

37

myQ

®

App Control

Connect With Your Smartphone

YOU WILL NEED:

l

Wi-Fi® enabled smartphone, tablet or laptop

l

Broadband Internet connection

l

Wi-Fi® signal in the garage

(2.4 GHz, 802.11b/g/n required)

, see page 5

l

Password for your home network (router's main account, not guest network)

l

myQ® serial number located on the garage door opener

DOWNLOAD THE myQ® APP TO SET UP AN ACCOUNT AND CONNECT

Open and close your door, get alerts and set schedules from anywhere. Connected smart garage door
openers also receive software updates to ensure the opener has the latest operational features.
The garage door opener must run through a complete cycle before it will activate Wi-Fi® programming.

1.

Download the myQ® App.

2.

Set up an account and connect.

If you already have the myQ® App installed:

1.

Check that your mobile device has the latest software.

2.

Download the latest version of the myQ® App.

For more information on connecting your garage door opener, visit support.chamberlaingroup.com.

NOTES:

myQ® App control WILL NOT work if the garage door opener is operating on battery power.
To erase the Wi-Fi® settings from the opener, see page 41.

Google Play and the Google Play logo are trademarks of Google LLC.
App Store and the Apple and App Store logos are trademarks of Apple Inc.

An LED on the garage
door opener will indicate
Wi-Fi status. See table
below.

LED

Learn
Button

Wi-Fi Status

LED

Definition

Blue

Off

- Wi-Fi® is not turned on.

Blinking

- Garage door opener is in Wi-Fi® learn mode.

Solid

- Mobile device connected to the garage door opener.

Blue and Green

Blinking

- Attempting to connect to router.

Green

Blinking

- Attempting to connect to the Internet server.

Solid

- Wi-Fi® has been set up and garage door opener is connected to the Internet.

«
...
35
36
37
38
39
...
»

Summary of Contents for C2212T





















































Reviews:

No comments

Related manuals for C2212T

Brand: FAAC Pages: 6

Brand: EasyGate Pages: 6

Brand: CAME Pages: 2

Brand: CAME Pages: 28

Brand: FAAC Pages: 9

Brand: Nice Pages: 36

Brand: CAME Pages: 30

1280LMC-R 1/2 HP

Brand: Chamberlain Pages: 72

Brand: C.C.E. Pages: 2

Brand: Dominator Pages: 32

Brand: Cardin Elettronica Pages: 44

Brand: Cardin Pages: 52

Brand: Cardale Pages: 6

Brand: Etdoor Pages: 17

Brand: CAME Pages: 144

LEPUS 2000 TRIFASE

Brand: SEA Pages: 16

Brand: Elite Pages: 22

Brand: Elite Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands