manualshive.com logo in svg

Chamberlain BMT 5011U, User Manual

Share
Download
Chamberlain BMT 5011U User Manual Download Page 3

3

Photoelectric Sensor

ALTERNATE INSTALLATION: C2 WIRING TYPE WITH MONITORED 
ENTRAPMENT PROTECTION DEVICE

•   Momentary contact to open and stop with constant pressure to 

close.

•   Open override that reverses when closing by any opening 

device.

•   Wiring for entrapment protection device to reverse.

NOTE: 

The operator will automatically convert to B2 wiring 

when Monitored Entrapment Protection Device is installed. (See 
accessories page for Monitored Entrapment ProtectionDevices.)

•  Timer-to-Close (TTC) feature not available.

Press and hold the LEARN and CLOSE buttons until the LED 
goes out (approximately 3 seconds). 

MONITORED ENTRAPMENT PROTECTION DEVICE

To Program:

TTC

LED

AUX ANT

R27

L5

TP1

C20

C9

C29
R24

J2

C21

J4

K2

LT

P1

C32

U4

D7

D6

D5

D4

R25

U1

C31

D14

C18

014A1030

^^^^

D9

LEARN

1

2

3

4

5

6

7

LMEP1

LMEP2

INTRLK

COM

STOP

CLOSE

OPEN

STOP CLOSE OPEN

AUX ANT

Logic Board

Electrical Box

D14

LED

LEARN

1

2

3

4

5

6

7

STOP

CLOSE

OPEN

ALTERNATE INSTALLATION: C2 WIRING TYPE WITHOUT 
MONITORED ENTRAPMENT PROTECTION DEVICE 

(FACTORY DEFAULT)

•   Momentary contact to open and stop with constant pressure to 

close.

•   Open override that reverses when closing by any opening 

device.

 •   Wiring for entrapment protection device to reverse.

NOTE: 

The operator will automatically convert to B2 wiring 

when Monitored Entrapment Protection Device is installed. 
(See accessories page for Monitored Entrapment Protection 
Devices.)

•  Timer-to-Close (TTC) feature not available.

NON-MONITORED ENTRAPMENT PROTECTION DEVICE

Sensing Edge

Remove any monitored entrapment protection devices.

Press and hold the LEARN and STOP buttons until LED goes 
out (approximately 3 seconds).

Reset to FACTORY DEFAULT (C2) without Monitored Entrapment 
Protection Device:

1

1

2

BASIC PROGRAMMING

DETERMINE THE WIRING TYPE

To Reset to B2 with Monitored Entrapment Protection Device:

Press and hold the LEARN and STOP buttons until the LED 
goes out (approximately 3 seconds).

1

Summary of Contents for BMT 5011U













Reviews:

No comments

Brands by name

Popular brands

Load more brands