Chamberlain B970 Owner'S Manual Download | Manualshive

Page: 19 / 44

background image

19

Installation

STEP 9 Connect the door arm to the trolley (continued)

OPTION B - ONE-PIECE DOORS

IMPORTANT:

The groove on the straight door arm MUST face away from the curved door arm.

1.

Close the door. Disconnect the trolley by pulling the emergency release handle.

2.

Fasten the straight door arm and the curved door arm together to the longest possible length (with a 2 or 3
hole overlap) using the bolts, nuts, and lock washers.

3.

Attach the straight door arm to the door bracket using the clevis pin. Secure with the ring fastener.

4.

Attach the curved door arm to the trolley using the clevis pin. Secure with the ring fastener.

5.

Pull the emergency release handle toward the garage door opener until the trolley release arm is
horizontal.

HARDWARE

Hex Bolt 5/16"-18x7/8"

Nut 5/16"-18

Lock Washer
5/16" -18

Clevis Pin 5/16"x1"

Clevis Pin 5/16"x1-1/4"

Ring Fastener

One-Piece Door without Track

One-Piece Door with Track

Ring Fastener

Ring Fastener

Ring Fastener

Nut

Nut

Ring Fastener

Lock Washer

Lock Washer

Clevis Pin 5/16"x1-1/4"

Clevis Pin
5/16"x1-1/4"

Hex Bolts

Hex Bolts

Clevis Pin
5/16"x1"

Clevis Pin
5/16"x1"

Straight Door Arm

(Groove facing out)

Curved Door Arm

«
...
17
18
19
20
21
...
»

Summary of Contents for B970













































Reviews:

No comments

Related manuals for B970

Brand: Dieffematic Pages: 10

Brand: CAME Pages: 30

Brand: FAAC Pages: 32

Brand: Hydro Doors Pages: 6

Brand: Centurion Pages: 40

Brand: Centurion Pages: 96

Brand: Hamilton Beach Pages: 8

Brand: MAG Pages: 9

Brand: digigate slider Pages: 7

Brand: Dea Pages: 58

Brand: Beninca Pages: 2

Brand: Nice Pages: 88

Brand: Calimet Pages: 17

Garage Door Kit 3

Brand: Yolink Pages: 49

Brand: Daspi Pages: 35

Brand: vds Pages: 8

Brand: GATEMASTER Pages: 13

Brand: Genie Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands