ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer purchaser of
this product that it is free from defect in materials and/or workmanship for
a period of 1 year from the date of purchase.
REPLACEMENT PARTS
Description
Part Number
3V 2032 Lithium battery
K010A0020
Visor Clip
K029B0137
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
The lithium battery should produce power
for up to 5 years. If the remote control’s
LED will not flash when the button is
pressed, replace the battery.
1.
Pry open the case with the visor clip,
first in the middle (1), then at each
side (2 and 3).
2.
Remove the old battery. Dispose of
old batteries properly.
3. Insert
replacement
batteries
positive
side up. Replace the batteries with
only 3V CR2032 coin cell batteries.
4. Replace
the
cover.
© 2020, The Cahmberlain Group Inc.
114-5496-000
All Rights Reserved
www.chamberlain.com
PROGRAM TO ALL GARAGE DOOR OPENERS
(CONTINUED)
Option B: Program Using the Smart Control Panel
5.
On the Smart Control Panel, press the MENU button.
6.
Use the arrow buttons to scroll to “PROGRAM”, and select
to
the next screen.
7.
Scroll down to “REMOTE,” and select
.
8.
Press and hold the button on the remote until the garage door lights
blink or two clicks are heard. Release the button. Programming is
complete.
9.
Test by pressing the remote control button you just programmed. The
opener activates.
Option C: Program Using the Multi-Function Door Control or
Motion Sensing Door Control
5.
On the door control, press the LEARN button twice.
6.
Press and hold the button on the remote until the garage door lights
blink or two clicks are heard. Release the button. Programming is
complete.
7.
Test by pressing the button you just programmed. The opener
activates.
Option D: Program Using the Garage Door Opener
5.
Press and release the LEARN button on the garage door opener. The
Learn LED will light. Within 30 seconds...
6.
Press and hold the remote control button until the garage door opener
lights flash or two clicks are heard. Release the button. Programming
is complete.
7.
Test by pressing the button you just programmed. The garage door
will activate.
HOW TO USE THE REMOTE CONTROL
Press and hold the button until the door or other programmed device starts
to move. The remote control will operate from 1 to 3 car lengths away on
typical installations. Installations and conditions vary.
ERASE REMOTE CONTROL PROGRAMMING FROM THE
OPENER
The following steps will erase ALL remote controls and any keyless entries
from your opener.
1.
Press and hold the LEARN button on the garage door opener until the
Learn LED turns off (approximately 6 seconds).
2.
Test by pressing the button on the remote control to ensure it no
longer activates the opener.
3.
Follow programming steps to reprogram the remote control.
REPLACE THE REMOTE CONTROL BATTERY
Multi-Function Door Control
Motion Sensing Door Control
To prevent possible SERIOUS INJURY or DEATH:
•
NEVER allow small children near batteries.
•
If battery is swallowed, immediately notify doctor
To reduce risk of fire, explosion or chemical burn:
•
Replace ONLY with 3V CR2032 corn batteries.
•
DO NOT recharge, disassemble, heat above 212°F (100°C)
or incinerate.
2
3
1
3V CR2032
For more information and support, go to:
support.chamberlaingroup.com
5
TO REMOTE
6
7