background image

 

•  Open your door to the highest point

of travel as shown. Draw an inter-
secting horizontal line on the header
wall 3" above the  high point. This
height will provide travel clearance
for the top edge of the door.

  

Header

Wall

Ceiling

Sectional door 

with curved track

One-piece door

with horizontal track

Track

Highest Point

of Travel

Door

Door

Track

SECTIONAL DOOR AND

ONE-PIECE DOOR WITH TRACK

3"

Header

Wall

Highest Point

of Travel

3"

8

 

Proceed to  Step 2, page 10.

The Chamberlain Group, Inc.
Position Header Bracket
Sectional and One-Piece Track Installations
1/30/92 - 4/6/92

SECTIONAL DOOR AND

ONE-PIECE DOOR WITH TRACK

Vertical

Guideline

Finished

Ceiling

Vertical

Guideline

Header

Wall

2x4

Structural

Supports

SECTIONAL Door or

ONE PIECE Door with Track

•  Close the door and mark the inside

vertical centerline of the garage door.

•  Extend the line onto the header wall

above the door.

Remember, you can fasten the header
bracket within 2 feet of the left or right
of the door center 

 

only if a torsion

spring or center bearing plate is in the
way; or you can attach it to the ceiling
(refer to page 10) when clearance is
minimal. (It may be mounted on the
wall upside down if necessary, to gain
approximately 1/2".)

 

If you need to install the header bracket on
a 2x4 (on wall or ceiling), use lag screws
(not supplied) to securely fasten the 2x4 to
structural supports as shown here and on
page 9. 

Installation Section:  Pages 8 – 23

Sectional door

with curved track

One-piece door 

with horizontal track

Installation Step 1

Determine Header Bracket Location

Installation procedures vary according to garage
door types. Follow the instructions which apply to
your door.

If the header bracket is not rigidly fastened to a
structural support on the header wall or ceiling, the
safety reverse system may not work properly (see page
26). 

The door might not reverse when required, and

could cause serious injury or death.

The garage door springs, cables, pulleys, brackets and
their hardware are under extreme tension. 

Do not attempt

to loosen, move or adjust them yourself. Serious
personal injury or death could result.  Call for
professional garage door service.

WARNING

CAUTION

WARNING

Summary of Contents for 1000SDR 1/3 HP





































Reviews: