Grass Trimmer - Operation
-9-
3. Do not overload your trimmer, take
small 'bits' this will keep machine
operating at high speed and will greatly
improve cutting efficiency, see dia13
and dia14.
4. Use the edge of the guard as a guide
when using near fences walls etc, and
move in a backwards direction, this will
save damage, see Dia 15 and Dia 16.
REPLACING THE CUTTING LINE
Warning! Always remove the battery
pack before carrying out any
maintenance
Note: Use the same diameter nylon line
for replacement, DO NOT use metal or
other material line.
1. To replace the nylon line, first remove
the spool cover from the spool holder by
pressing the spool cover locking
mechanism from the both sides and at
the same time hold the bottom of the
cutting head firmly. Rotate the spool
cover as Dia 17 and 18 direction, the
spool cover will spring up.
2. Insert the line into the small hole in the
end spool and wind the line around the
spool in direction as shown in Dia 19
Note: the line must be wound uniformly
around the spool, or you may
Dia. 17
Dia 12
Grass Trimmer - Operation
-9-
3. Do not overload your trimmer, take
small 'bits' this will keep machine
operating at high speed and will greatly
improve cutting efficiency, see dia13
and dia14.
4. Use the edge of the guard as a guide
when using near fences walls etc, and
move in a backwards direction, this will
save damage, see Dia 15 and Dia 16.
REPLACING THE CUTTING LINE
Warning! Always remove the battery
pack before carrying out any
maintenance
Note: Use the same diameter nylon line
for replacement, DO NOT use metal or
other material line.
1. To replace the nylon line, first remove
the spool cover from the spool holder by
pressing the spool cover locking
mechanism from the both sides and at
the same time hold the bottom of the
cutting head firmly. Rotate the spool
cover as Dia 17 and 18 direction, the
spool cover will spring up.
2. Insert the line into the small hole in the
end spool and wind the line around the
spool in direction as shown in Dia 19
Note: the line must be wound uniformly
around the spool, or you may
Dia. 17
Dia 12
Dia. 18
experience some line breakage or
vibration.
3. Insert the line through the hole in the
spool cover, pull the line out( to save it
snagging in cutting head body and
lower the spool at an angle) see Dia 20.
4. Push spool with spool cover against the
spring firmly downwards till it lowers into
position. Depressed the locking
mechanism inwards, then turn in arrow
direction till it locks in place, release the
locking mechanism, now the spool
cover is replaced. See dia 21.
Follow the instruction on cutting the line in
"preparing the trimmer for use" section 2
and 3. Before use.
Note:
New line can be purchased from
any good garden or DIY center.
Warning! Always let the machine run
for 1-2 mins to check if the cutting head
is in good condition. If noise or
vibration found, switch off and remove
the battery, refit the spool cover.
MAINTENANCE AND STOREAGE
Important note:
Always remove battery
before cleanning, repair and
storage.
1. Always remove the battery pack
whenever you carrying out any cleaning
or repair.
2. Your tool requires no additional
lubrication or maintenance. There are
no user serviceable parts in your tool.
3. Never use water or chemical cleaners to
clean your power tool. Wipe clean with a
dry cloth.
4. Always check the cutting head and
guard before each use.
5. Always store your power tool in a dry
place.
6. Keep the motor ventilation slots clean.
7. Have the unit professionally repaired
should any damage occurs.
TROUBLE
SHOOTING
Although your new cordless grass trimmer
is really easy to operate. If you do
experience problems, check the following:
If grass trimmer will not operate
l
Check battery pack assembly
l
Charge the battery: running of the grass
trimmer is dependent upon sufficient
charge in the battery pack. The battery
charge will deplete if not used for a long
period of time. Try recharging the
battery pack. Ensure that the battery
pack is fully contacted charger base.
Note:
The battery pack will only fit into the
charger with + to + and - to -. The charger
will not operate at extremes of temperature.
The charger will get warm during charging
but this is normal.
If the battery will not charge
Check to see if the battery is properly
inserted the charger base, and make sure
the indicator light is on, if not check the
mains supply.
If the trimmer is not cutting properly
Check the condition of the cutting head, if
the cutting line is too short or cutting head
damaged.
Note: do not use damaged
cutting head.
Dia. 20
Spool cover
Locking
mechanism
on both sides
Dia. 19
Hole in the
end speel
Dia. 21
2
1
Grass Trimmer - Operation, Maintenance and Troubleshooting
Dia. 1
5
Dia. 1
6
