background image

Operating the Digital Home Safe  

Operating the Digital Home Safe  

Important : Please read the instructions thoroughly before beginning the set-up  
 procedure. 

Dia 1 

Dia 4

-1- 

-2- 

Locking knob 

Orange 
  LED 

Red 
 LED 

Green 
  LED 

Electronic Key Pad 

Lock Cover 

Concealed 
  Hinges 

Dia 2

White Cap covering 
Reset Button

Dia 3

Reset Button

Battery Cover

Operating Instructions

Note: Please make sure that after you have opened 
 

the safe for the first time, you change the PIN, 

 

for security reasons.

OPERATING THE SAFE FOR THE FIRST TIME

1. Use the Manual override key to open the safe for the first time, 
  a) Remove the plastic key lock cover (Dia 1)
  b) Insert the override key, turn to the left and at the same time 
  turn the safe handle to the right and open the safe .
2. Remove the battery cover on the rear of the door (Dia 3) and 
  install the 4X AA type batteries supplied, in the back of the safe 
  door, as shown in Dia 5 and replace the battery cover.
3. While the door is open familiarise yourself with the door 
  opening procedure, and leave the door open until you are 
  happy with the method of opening the safe door.
  To set the safes PIN code for the first time please follow these  
 instructions.
  Remove and retain the white cap covering the red reset button 
  (located at the back of the door, see Dia 2 & Dia 3)
  Press red reset button once
  Press '159159' on the keypad as a code
  Press 'B' once
  The PIN code has now been set to '159159'.
  Replace the white cap over the reset button (for security reasons).
  To open the safe using the PIN code:
  Press 'B' once
 Press 

'159159'

  Press 'B' once
  The green LED will come on, the door internal lock will disengage and you can now turn the 
  door knob clockwise and open the door.

4. Refit the plastic key cover and place the override keys in a safe place (NOT IN THE SAFE) for 
 emergency 

use.

WARNING:

 NEVER keep the override keys inside the safe.

Programming Your Personal identification Number (PIN)

1. With the door open, remove the white cap (Dia 2)and depress the red reset button (Dia 3) 
  located at the back of the door near the top hinge. 
2. A beep will be heard and the orange LED will illuminate. Key in your new PIN (any 
  combination of numbers from 3 to 8 digits) then press “B”. Be sure to write down this PIN 
  number so you do not forget. 
3. The safe will now lock when you close the door and turn the knob anti-clockwise. 
4. To open the safe again, Press the “B” button then your PIN number followed by the “B” button, 
  you can now open the safe door by turning the knob clockwise. 
 
Note if the incorrect PIN is entered the keypad will freeze for 20 seconds

5. To alter the PIN at any time follow the steps in instructions above 
6. Screw the white cap back onto the red reset button when your pin has been reset for security 
 reasons. 
 

CAUTION:

If an incorrect PIN is entered the safe will not open and three warning beeps will be heard. 
Entering an incorrect PIN three consecutive times will freeze the locking mechanism and 
keypad for 20 seconds during which time you will not be able to operate the safe.

Opening Safe with Key

You can use the manual override key to open the safe and reset your 

PIN

DO NOT 

keep the override key in the safe.
 
1. To use the key, remove the small lock cover in the centre of the control panel. 
2. Turn the key anticlockwise, then the doorknob clockwise, and the door will open.
Please keep the keys in a secure place, as we do not supply replacement keys, for
security reasons.    

Securing your Safe

You may wish to secure your safe to a fixed
part of the house (i.e.  a steel panel or wooden
beam).This can be achieved by using the four 
bolts supplied. Insert the bolts through the 4
pre-made holes on the back or bottom of the 
safe.  (See Dia 4).

Note

:

Bolts are packed inside the safe (on the mat).
When fitting the bolts ensure that the nuts are 
on the inside of the safe.

Reviews: