manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 94

 

 

 

MAY 2019 

 

2. Status Indicator RAPs

 

2-82 

CMT-130TC Book Trimmer 

RAP 2.74 Stacker Book In Tray Sen-
sor 

Stacker I/O PWB Input 4 

The book in tray sensor is a retro-reflective sen-
sor that detects when books have completely 
entered into the roller tray.  This triggers the tray 
up/down cylinder and tray dump cylinder to actu-
ate, dropping the book onto the output tray. 

The sensor is mounted in the bottom of the roller 
tray.  The reflector is directly above the sensor, 
as shown in Figure 2-113. 

Possible Fault Indicators 

 

“Stacker Book Jam at Input”

 

message is displayed when there is no 
jam. 

 

A jam is not detected when there is a 
book stuck on the roller tray. 

 

The roller tray never tilts to drop a book. 

Initial Actions 

Check that the sensor is aligned with the reflec-
tor mounted above it.   

Check that all cables between the trimmer and 
Stacker are securely fastened and are not dam-
aged. 

Check and repair loose or damaged wires 65, 
73, and 74 at the Stacker electrical panel. 

Procedure 

1.  Switch the main power ON and go to the 

Stacker diagnostic screen (GP 6.2 In-
put/Output Diagnostics).  Make sure that the 
sensor is not obstructed.  Is input “Book In” 
off? 

Y  N 

Disconnect wire 65.  On the diagnostic 
screen does input “Book In” switch off? 

Y  N 

Disconnect power and replace the 
Stacker I/O PWB (REP 4.26 Accessory 
PWB Replacement). 

Adjust the sensor (GP 6.6 Retro-reflective 
Sensors) and replace if faulty (PL 5.58 Out-
feed Stacker 58000TCA (4/9) or PL 5.64 
Stacker Elec. Panel EE-3518). 

2.  Short wire 65 to 74.  On the diagnostic 

screen does input “Book In” switch on? 

Y  N 

Disconnect power and replace the Stacker 
I/O PWB (REP 4.26 Accessory PWB Re-
placement). 

3.  Adjust the sensor (GP 6.6 Retro-reflective 

Sensors) and replace if faulty (PL 5.58 Out-
feed Stacker 58000TCA (4/9) or PL 5.64 
Stacker Elec. Panel EE-3518). 

 

 

 

Figure 2-113. Book In Tray Sensor 

 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands