manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 77

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

2-65 

2. Status Indicator RAPs

 

RAP 2.57 Book In From Binder Sen-
sor 

Elevator I/O PWB Input 2 

The book in from binder sensor detects books 
entering the Tilt Infeed Conveyor.  This sensor 
also wakes the trimmer from sleep mode when 
triggered. 

Possible Fault Indicators 

 

The machine never enters sleep mode. 

 

Books accumulate in the tilt infeed con-
veyor. 

 

The machine does not return to ready 
mode. 

Initial Actions 

Check that all cables between the trimmer, Ele-
vator, and Tilt Infeed Conveyor are securely fas-
tened and are not damaged. 

Check for loose or damaged wires 42, 73, and 
74 at the Elevator electrical panel (Figure 2-86). 

Procedure 

1.  Switch the main power ON and go to the El-

evator diagnostic screen (GP 6.2 Input/Out-
put Diagnostics).  Make sure that the sensor 
is not obstructed.  

Is input “Book In From 

Binder” off? 

Y  N 

Disconnect wire 42 from the Elevator I/O 
PWB (Figure 2-86).  Does the input switch 
off? 

Y  N 

Disconnect power and replace the Ele-
vator I/O PWB (REP 4.26 Accessory 
PWB Replacement). 

Adjust the sensor (GP 6.7 Diffuse Sensors) 
and replace if faulty (PL 5.47 Tilt Conv. Elec. 
Panel EE-3547). 

2.  Short wire 42 to wire 74.  Does the input 

switch on? 

Y  N 

Disconnect power and replace the Elevator 
I/O PWB (REP 4.26 Accessory PWB Re-
placement). 

3.  Adjust the sensor (GP 6.7 Diffuse Sensors) 

and replace if faulty (PL 5.47 Tilt Conv. Elec. 
Panel EE-3547). 

 

Figure 2-85. Book In From Binder Sensor 

 

 

Figure 2-86. Elevator Electrical Panel 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands