manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 62

 

 

 

MAY 2019 

 

2. Status Indicator RAPs

 

2-50 

CMT-130TC Book Trimmer 

RAP 2.42 Gripper Rotation Preset 
Sensor 

Input 6 

The rotator preset sensor is located on the grip-
per assembly as shown in Figure 2-66.  The 
sensor determines the home position of the rota-
tor assembly. 

Possible Fault Indicators 

 

Gripper rotator assembly does not pre-
set and continues to rotate. 

 

Gripper rotator does not rotate to proper 
position during initiation. 

Initial Actions 

Check for loose or damaged wire 52 at the elec-
trical panel. 

Procedure 

1.  Switch the main power OFF. 

2.  Manually move the rotator assembly such 

that the rotator disk covers the sensor. 

3.  Switch the main power ON and go to the di-

agnostic screen (GP 6.2 Input/Output Diag-
nostics). Does the diagnostic screen show 
input “Gripper Rotation Preset” on? 

Y  N 

Short wire 52 to wire 74.  On the diagnostic 
screen does input "Gripper Rotation Preset" 
switch on? 

Y  N 

Disconnect power and replace the main 
PWB (REP 4.23 Main PWB Replace-
ment). 

Adjust the sensor (GP 6.5 Proximity Sen-
sors) and replace if faulty (PL 5.7 Main As-
sembly 59000 (7/14)). 

4.  Disconnect wire 52.  On the diagnostic 

screen does input " Gripper Rotation Preset 
" switch off? 

Y  N 

Disconnect power and replace the main 
PWB (REP 4.23 Main PWB Replacement). 

5.  Adjust the sensor (GP 6.5 Proximity Sen-

sors) and replace if faulty (PL 5.7 Main As-
sembly 59000 (7/14)). 

 

 

Figure 2-66. Rotator Preset Sensor 

 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands