manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 228

 

 

 

MAY 2019 

 

6. General Procedures/Information

 

6-14 

CMT-130TC Book Trimmer 

GP 6.13 Contact Blocks 

This procedure is used to check pushbutton 
switch contact blocks for faults.  Normally closed 
contact blocks have a red actuator, and normally 
open contact blocks have a green actuator. 

Initial Actions 

WARNING 

Disconnect and lockout power as described 
in the Power Lockout Procedure on page ix. 

Procedure 

1.  Remove the lever lock as shown in Figure 

6-16. 

2.  Rotate the lever from one side of the contact 

block to the other in order to release it from 
the switch body.  Pull the contact block off 
the pushbutton body. 

3.  Make note of where each wire enters the 

contact block then disconnect the wires from 
the contact block. 

4.  Press and release the actuator.  Does the 

actuator return freely? 

Y  N 

The contact block is faulty and should be re-
placed. 

Normally Open Contact 

5.  Check resistance between contact screws.  

Is resistance infinite? 

Y  N 

The contact block is faulty and should be re-
placed. 

6.  Press the actuator and check resistance be-

tween contact screws.  Is resistance less 
than 2 Ohms? 

Y  N 

The contact block is faulty and should be re-
placed. 

7.  The contact block is good. 

8.  Re-install switch. 

Normally Closed contact 

9.  Check the resistance between contact 

screws.  Is resistance less than 2 Ohms? 

Y  N 

The contact block is faulty and should be re-
placed. 

10.  Press the actuator and check resistance be-

tween contact screws.  Is resistance infinite? 

Y  N 

The contact block is faulty and should be re-
placed. 

11.  The contact block is good. 

12.  Re-install switch. 

 

 

Figure 6-16. Contact Block 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands