manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 224

 

 

 

MAY 2019 

 

6. General Procedures/Information

 

6-10 

CMT-130TC Book Trimmer 

GP 6.9 Barcode Scanner 

The CMT-130TC uses a barcode scanner to 
scan barcodes printed on the covers of books as  
they enter the trimmer.  The trimmer uses the in-
formation in the barcode to set trim sizes for 
each book.   

For more information about the barcode capabil-
ities and settings, see the CMT-

130TC’s 

Installa-

tion and Opera

tor’s Manual

. 

The barcode scanner can be reset if necessary 
using the following procedure. 

Procedure 

1.  Switch the main power ON and press the 

green start button to initialize the trimmer.   

2.  Press the "Job" button, then press the "Bar 

Code" button to open the barcode job 
screen.   

3.  Near the lower right of the screen (Figure 

6-12), select the desired barcode format 
(Code 128, Data Matrix, etc.). 

4.  Now press the "Program Bar

C Reader” but-

ton at the lower right corner of the screen.  

5.  The barcode scanner should emit a brief se-

quence of beeps indicating that the pro-
gramming was successful for the selected 
barcode format. 

 

 

Figure 6-11. Barcode Scanner 

 

 

Figure 6-12. Barcode Job Screen 

 

 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands