manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 15

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

2-3 

2. Status Indicator RAPs

 

RAP 2.2 Error Messages 

An error message will appear on the display 
screen often times when there is a fault. The fol-
lowing table contains the complete list of possi-
ble error messages. Always attempt to resolve 
and clear the error message before performing 
the recommended procedures in this list (for ex-
ample, for an open door message, close the 
door).  It may be necessary to switch the power 
OFF and back ON in order to clear the mes-
sage.  If the error message cannot be resolved 
or continues to be displayed, follow the associ-
ated recommended procedures shown below. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Error Messages (in Alphabetical Order) 

Recommended Procedures 

Accuracy is out of range 

ADJ 4.5 Accuracy Adjustment 

Bar Code Error 

RAP 2.50 Barcode Scanner 

Book At Thickness Sensor Unexpectedly 

RAP 2.47 Book Entering CMT Sensor 
RAP 2.49 Book Thickness Sensor 

Book finish length outside limits 

See 

Installation and Operator's Manual 

for allowed dimensions

 

Book finish width outside limits 

See 

Installation and Operator's Manual 

for allowed dimensions

 

Book in Elevator JAM Error 

RAP 2.60 Book Entering Elevator Sensor 
RAP 2.54 Elevator Tilt Infeed Motors 
RAP 2.55 Elevator Lift Motor 

Book Start length outside limits  

See 

Installation and Operator's Manual 

for allowed dimensions 

Book Start width outside limits 

See 

Installation and Operator's Manual 

for allowed dimensions

 

Book Thickness value too large 

See 

Installation and Operator's Manual 

for allowed dimensions 

Book Length & Trim combination too large 

See 

Installation and Operator's Manual 

for allowed dimensions 

Book did not reach Width sensor in time 

RAP 2.48 Book Width Sensor 

Connection Lost to I/O Motor Controller! 

RAP 2.6 Touch Screen Display 

EE memory Read Fail 

GP 6.4 Updating Machine Software 
REP 4.24 Console PWB Replacement 

EE memory Write failed 

GP 6.4 Updating Machine Software 
REP 4.24 Console PWB Replacement 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands