Chal-tec 10009110 Manual Download Page 16

 

 

IMPORTANT SAFETY INSTRUCTIONS

 

Read all the instructions in this manual carefully before using your equipment 

WARNING:

 Before beginning this or any exercise program, consult your physician. This is especially 

important for persons who have not exercised regularly before or persons with pre-existing health problems. 

Read all instructions before using. Manufacturer assumes no responsibility for personal injury or property 

damage sustained by or through the use of this equipment. 

WARNING

: Any contamination alteration or misuse would dangerously reduce the performance of the 

protector. 

WARNING

: Any changes in environmental conditions such as temperature would significantly reduce the 

performance of the protector. 

WARNING

: No protector can offer full protection against injures. 

 

1.

 

It is the responsibility of the owner to ensure that all users of this equipment are adequately 

informed of all warnings and precautions. 

2.

 

Use the equipment only as described in this manual. 

3.

 

Place on a level and stable surface, with 2 meter of clearance around it. To protect the floor or 

carpet from damage, place a mat under this equipment. 

4.

 

Keep the equipment indoors, away from moisture or dust. Do not put the equipment in a garage, 

shed, conservatory, outbuilding or covered patio, or near water. Failure to do this will invalidate your 

warranty and could cause serious safety problems. 

5.

 

Do not operate the equipment where aerosol products are used or where oxygen is being 

administered. 

6.

 

Keep children under the age of 12 and pets away from the equipment all the time. 

7.

 

The equipment should not be used by persons weighting more than 110kg. Serious injury may occur 

if the user weight exceeds the limit shown here. 

8.

 

The equipment complies with class HC of the standard EN957. 

9.

 

Never allow more than one person on the equipment at a time. 

10.

 

Wear appropriate exercise clothing when using the equipment. Do not wear loose clothing that could 

become caught in the equipment. Athletic support clothes are recommended for both men and 

women.  

11.

 

If you feel pain or dizziness while exercising, stop immediately and cool down. 

12.

 

The pulse sensor is not a medical device. Various factors, including the user’s movement, may affect 

the accuracy of the heart rate readings. The pulse sensor is intended only as an exercise aid in 

determining heart rate trends in general. 

13.

 

This equipment is intended for home use only. Do not use in a commercial or institutional setting. 

 

 

 

 

 

 

 

 

 

STORE THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE 

Summary of Contents for 10009110





























Reviews: