manualshive.com logo in svg

CHAINTECH 6AFV, Manual

Share
Download
CHAINTECH 6AFV Manual Download Page 20

Hardware Setup

17

USB 0/1Ports and USB 2/3 Connector (USB1/CN14)

If  you  want  to  use  a  USB  keyboard,  you  must

enable  the  USB  keyboard  support  function  in

BIOS's Integrated Peripherals menu (See Section

3-4).
This  board  contains  a  USB  Host  controller  and

includes  a root hub with two USB ports (meets

USB Rev 1.0 spec.) and a connector for optional

USB Adaptor (USB2/3).  Four USB peripherals or

hub  devices  are  able  to  be  connected.

Optional TV-Out/DFP Connectors (CN19A/CN19B)

The connectors are to be connected to an optional

TV-Out/DFP adapter card.

Front Panel Audio Connector (CN29)

This connector give you the option to choose
between standard audio jack(rear panel) or use a
an optional front panel audio jack cable ext. to
be plug into a special custom designed system
case.
To use the standard audio jack short jumper caps
to pin1-2 and pin 3-4 (Default). To use the  front
panel audio jack cable ext., simply removed both
jumper caps and plug into the audio jack cable.

Standard Rear Panel

Front Panel

Summary of Contents for 6AFV
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands