background image

NORSE by C.H. Hanson warrants their products to be free of defects in material or workmanship. This
warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure
to properly maintain the product, heated, ground or otherwise altered, or used for a purpose other than
that for which it was intended.

The warranty does not cover expendable and/or wear part (i.e. v-belts, screws, abrasives, jaws), damage to
tools arising from alteration, abuse or use other than their intended purpose, packing and freight. The
duration of this warranty is expressly limited to the terms noted below beginning from the date of
delivery to the original user.

The NORSE branded items carry the following warranties on parts:

All NORSE branded Tools and Accessories 1 YEAR

The obligation of NORSE by C.H. Hanson is limited solely to the repair or replacement, at our option, at its
factory or authorized repair agent of any part that should prove inoperable. Purchaser must lubricate and
maintain the product under normal operating conditions at all times. Prior to operation become familiar
with product and the included materials, i.e. warnings, cautions and manuals.

Failure to follow these instructions will void the warranty.

This warranty is the purchaser's exclusive remedy against C. H. Hanson for any inoperable parts in its
product. Under no circumstances is C. H. Hanson liable for any direct, indirect, incidental , special or
consequential damages including loss of profits in any way related to the use or inability to use our
products. This warranty gives you specific legal rights which may vary from state to state.

SERVICE & REPAIR

1. If a NORSE product requires a repair or warranty service 

DO NOT

return the product to 

the place of purchase. 

2. All warranty related work must be evaluated and approved by NORSE.

3. Prior to returning any item the user must obtain factory approval and a valid RGA number. 

4. For instructions and RGA number call toll free (800) 827-3398.

NORSE - a C.H. Hanson brand

2000 N. Aurora Rd., Naperville, IL 60563  U.S.A.

or call:

1-800-827-3398

NORSE Operating Manual & Parts List

9681119

NORSE Warranty

9681119_oipm_En012_9643311.01  03/21/18  Page 12

Summary of Contents for Norse 9681119













Reviews: