VER. 001_04.07.2011
MOUNTING
'LVFRQQHFW SRZHU VXSSO\ E\ WKH SKDVH IXVH
the circuit-breaker or the switch-disconnector
combined to the proper circuit.
2. Check if there is no voltage on connection ca-
bles by means of a special measure equipment.
3. Carefully remove upper cover undoing the
VFUHZV¿UVW
4. Choose a place on the wall for mount-
ing the temperature controller;; make two
holes in the wall corresponding mounting
holes of the temperature controller’s base.
5. Set wall plugs in the holes.
6. Insert installation wires through the holes in
the base.
7. Mount the base by means of screws (screw
them into the wall plugs).
8. Connect the cables with the terminals in ac-
cordance with the installing diagram.
9. Connect external sensor to RT2-, RT2+ termi-
nals if necessary.
10. Adjust regulator’s operation parameters by
means of operation mode switch.
11. Place the upper cover on the base.
12. Screw the regulator’s base. Only ø3 mm screws
can be used wit maximum length of 8 mm.
13. Switch on the power supply from the mains
and check the regulator’s operation.
&$87,216ZLUHZLWKÀRRUVHQVRUPXVWQRW
be shortened.
FUNCTIONING
CONNECTION
/&'GLVSOD\VKRZVFXUUHQWURRPWHPSHUDWXUHGXULQJLWVRSHUDWLRQ&XUUHQWWHPSHUDWXUHDGMXVWPHQWLV
shown in pulsating form while turning the knob.
7HPSHUDWXUHDGMXVWPHQW
$GMXVWUHTXLUHGWHPSHUDWXUHE\PHDQVRIDWHPSHUDWXUHFRQWUROOHU¶VNQRE,WZLOOSXOVDWHRQWKH/&'
GLVSOD\$IWHUDVKRUWWLPHWKH/&'GLVSOD\VWRSVSXOVDWLQJDQGVKRZVFXUUHQWURRPWHPSHUDWXUH
+HDWLQJVWDWXVÀDPHV\PERODSSHDUVZKHQWKHUHJXODWRUVWDUWVKHDWLQJ
&RROLQJVWDWXVVQRZÀDNHV\PERODSSHDUVZKHQWKHUHJXODWRUVWDUWVFRROLQJ
The regulator has (internal) built-in temperature sensor and terminals signed RT2-, RT2+ used for
H[WHUQDOÀRRUWHPSHUDWXUHVHQVRUFRQQHFWLRQ,IWKHH[WHUQDOVHQVRULVFRQQHFWHGWRWHUPLQDOVWKHQ
the temperature is controlled by the external sensor. Otherwise the regulator uses the built-in sensor.
(UURUWDEOH(UURUV\PEROSXOVDWHVRQWKH/&'GLVSOD\
Symbol
'HVFULSWLRQ
„E1” pulsates
Short-circuit of internal sensor - temperature controller cuts off the output
„E2” pulsates
%UHDNRIH[WHUQDOÀRRUVHQVRUWHPSHUDWXUHFRQWUROOHUFXWVRIIWKHRXWSXW
„E3” pulsates
6KRUWFLUFXLWRIH[WHUQDOÀRRUVHQVRUWHPSHUDWXUHFRQWUROOHUFXWVRIIWKHRXWSXW
,QFDVHRIH[WHUQDOÀRRUVHQVRUEUHDNVWKHURRPWHPSHUDWXUHLVFRQWUROOHGE\LQWHUQDOEXLOWLQVHQVRU
,IWKHURRPWHPSHUDWXUHFRQWUROOHU¶VLVKLJKHUWKDQ&WKHÄ+,´V\PERODSSHDUVRQWKH/&'GLVSOD\7KHQ
in heating mode the temperature controller’s output is cut off whereas in cooling mode cooling should start.
,IWKHURRPWHPSHUDWXUHLVORZHUWKDQ&WKHÄ/2´V\PERODSSHDUVRQWKH/&'GLVSOD\
In the heating mode, heating should start but in the cooling mode - cooling should switch off.
WARRANTY CARD
There is 24 months guarantee on the product
6DOHVPDQVWDPSDQGVLJQDWXUHGDWHRIVDOH
1. CET Sp. z o.o. assures 24 months guarantee for the product.
2. The manufacturer’s guarantee does not cover any of the following actions:
a) mechanical damage during transport, loading / unloading or under other circumstances,
b) damage caused by incorrect product mounting or misuse,
FGDPDJHFDXVHGE\XQDXWKRULVHGPRGL¿FDWLRQVPDGHE\WKH385&+$6(5RUDQ\WKLUGSDUWLHVWRWKHSURGXFWRUDQ\RWKHUGHYLFHV
needed for the product functioning,
d) damage caused by Act of God or any other incidents independent of the manufacturer - CET Sp z o.o.
e) power supply (batteries) to be equipped with a device in the moment of sale (if they appear);;
3. The PURCHASER shall lay any claims in writing to the dealer or CET Sp. z o.o.
4. CET Sp. z o.o. is liable for processing any claim according to current Polish legislation.
5. CET Sp. z o.o. shall process the claim at its own discretion: product repair, replacement or money return.
6. The manufacturer’s guarantee is valid in the Republic of Poland.
7. The PURCHASER’s statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or
otherwise are not affected by this warranty.
ADJUSTMENT CONFIGURATION OF SWITCHES
2SHUDWLRQPRGHVVZLWFKDGMXVWPHQWGHIDXOWVHWWLQJV
'HOD\VIRUFRROLQJFRRSHUDWLRQZLWKFRPSUHVVRU
NODELAY
- compressor delay function is cancelled,
DELAY
- compressor’s 5 minute protective time.
0DLQVZLWFKDGMXVWPHQW
Function
'HVFULSWLRQ
Operation modes switch adjusted to:
Temperature controller in comfort mode - controlled temperature is consistent with the temperature adjusted by means of a knob.
Temperature controller in economical mode - controlled temperature is 4°C lower than the temperature adjusted by means of a knob
(heating function) or 4°C higer than the temperature adjusted by means of a knob (cooling function)
Operation modes switch adjusted to:
7+(5(/$<,66:,7&+('21&RQWUROOHGWHPSHUDWXUHLVFRQVLVWHQWZLWKWKHWHPSHUDWXUHDGMXVWHGE\PHDQVRIDNQRE
7+(5(/$<,66:,7&+('2))Ä2)´V\PERODSSHDUVRQWKHGLVSOD\
CAUTION: terminals 3 and 4
must be connected.
(OHFWULFDOV\VWHPRIÀRRUKHDWLQJ
:DWHUV\VWHPRIÀRRUKHDWLQJ
CAUTION: terminals 3 and 4 must not be connected.
Their connection can cause short circuit.
o
F
67$1'%<
(SWITCH ON/SWITCH OFF) ON/OFF
(Cooling) COOL
o
C
67$1'%<
/
HEAT (Heating)
o
F
12'(/$<
(SWITCH ON/SWITCH OFF) ON/OFF
(Cooling) COOL
o
C
'(/$<
/
HEAT (Heating)
HEATING
COOLING
FLOOR
HEATING
furnace
central
heating
