Cessna 152 1979 Pilot Operating Handbook Download | Manualshive

Page: 149 / 161

background image

CESSNA

SECTION

8

MODEL 152

HANDLING, SERVICE

&

MAINTENANCE

1 July 1978

8-14

ENGINE CARE

The engine may be cleaned with Stoddard solvent, or equivalent, then dried thoroughly

CAUTION

Particular care should be given to electrical equipment before cleaning.
Cleaning fluids should not be allowed to enter magnetos, starter alternator
and the like. Protect these components before saturating the engine with
solvents. All other openings should also be covered before cleaning the
engine assembly. Caustic cleaning solutions should be used cautiously
and should always be properly neutralized after their use.

INTERIOR CARE

To remove dust and loose dire from the upholstery and carpet, clean the interior regularly with
a vacuum cleaner.

Blot up any spilled liquid promptly with cleansing tissues or rags. Don’t pat the spot; press the
blotting material firmly and fold it for several seconds. Continue blotting until no more liquid is
taken up. Scrape off sticky materials with a dull knife then spot-clean the area.

Oily spots may be cleaned with household spot removers, used sparingly. Before using any
solvent, read the instruction on the container and test it on an obscure place on the fabric to be
cleaned. Never saturate the fabric with a volatile solvent; it may damage the padding and
backing materials.

Soiled upholstery and carpet may be cleaned with foam-type detergent, used according to the
manufacturer’s instructions. To minimize wetting the fabric, keep the foam as dry as possible
and remove it with a vacuum cleaner.

If your airplane is equipped with leather seating, cleaning of the seats is accomplished using a
soft cloth or sponge dipped in mild soap suds. The soap suds, used sparingly, will remove
traces of dirt and grease. The soap should be removed with a clean damp cloth.

The plastic trim, headliner, instrument panel and control knobs need only be wiped off with a
damp cloth. Oil and grease on the control wheel and control knobs can be removed with a
cloth moistened with Stoddard solvent. Volatile solvents, such as mentioned in paragraphs on
care of the windshield, must never be used since they soften and craze the plastic.

«
...
147
148
149
150
151
...
»

Summary of Contents for 152 1979


































































































































































Reviews:

No comments

Related manuals for 152 1979

Brand: Ikon Pages: 9

Brand: Advance acoustic Pages: 19

Brand: ASG Pages: 10

172 Series 1973

Brand: Cessna Pages: 77

172 Skyhawk SERIES

Brand: Cessna Pages: 167

Brand: Nova Pages: 41

UFM - 13 LAMBADA

Brand: Urban Air Pages: 91

Brand: Tecnam Pages: 162

Brand: E-FLITE Pages: 19

Brand: MAC PARA Pages: 32

Brand: MAC PARA Pages: 28

Brand: airwave Pages: 37

Brand: Ozone Pages: 20

Brand: Nova Pages: 43

FES-LAK-P10-100

Brand: LZ design Pages: 9

FES FES-DIS-P1-102

Brand: LZ design Pages: 10

Brand: LZ design Pages: 26

Brand: czech sport aircraft Pages: 113

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands