Century Helicopter Products Sikorsky S-61 Sea King Instruction Manual Download Page 1 | Manualshive

Page: 1 / 15

background image

Sikorsky Sea King

Fuselage Instruction Manual

Length: 54" Body nose to body tail.

Width: 18.5” Body left to right.

Height: 13” Body bottom to top.

Weight: 12-14 lbs. With full load of 60-90 size

mechanics and Radio equipment

Designed and Developed in the USA

Sept, 2002 All rights reserved.

SEA KING SPECIFICATIONS

Century Helicopter Products

Century has designed a new Sikorsky S-61 Sea King. Changes to
full-size helicopter designs are a direct challenge to the modeler. To
its predecessor, the Century model Sea King fuselage has many tiny
details to catch your eye, and major detail features make a tremen-
dous difference to the overall impression.

1
2
3
...
»

Summary of Contents for Sikorsky S-61 Sea King
















Reviews:

No comments

Related manuals for Sikorsky S-61 Sea King

MAISON FORSTIERE 8037

Brand: JEUJURA Pages: 2

Mickey Mouse Cafe

Brand: VTech Pages: 20

Kittyhawk Mk.Ia

Brand: Eduard Pages: 3

Brand: LEGO Pages: 64

Brand: H-KING Pages: 12

Weekend I-16 TYPE 10

Brand: Eduard Pages: 6

BUILDING SITE DECORATION

Brand: Faller Pages: 4

Brand: LeapFrog Pages: 13

F-4 Phantom-II FF-D007

Brand: Fly Fly Hobby Pages: 10

Brand: Kyosho Pages: 36

Piper Turbo Arrow IV

Brand: 3D AEROWORKS Pages: 28

EF 2000 Single Seater exterior

Brand: Eduard Pages: 3

Interior Kit T-60

Brand: MiniArt Pages: 18

Brand: POLA G Pages: 4

Brand: Fisher-Price Pages: 12

Brand: E-FLITE Pages: 20

Beach Bungalow House

Brand: Barbie Pages: 6

Brand: Magformers Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands