Centralion MaxPower 1000 User Manual Download Page 4

z

  Servicing of batteries should be performed or supervised by 

personnel knowledgeable of batteries and the required precautions.  
Keep unauthorized personnel away from batteries.

 

z

  When replacing batteries, replace with the same type and number of 

the sealed lead-acid batteries.   

z

  The maximum ambient temperature rating is 40

z

  This pluggable type A equipment with battery already installed by the 

supplier is operator installable and may be operated by laymen. 

z

  During the installation of this equipment it should be assured that the 

sum of the leakage currents of the UPS and the connected loads 
does not exceed 3.5mA. 

z

  Attention, hazardous through electric shock. Also with disconnection 

of this unit from the mains, hazardous voltage still may be accessible 
through supply from battery. The battery supply should be therefore 
disconnected in the plus and minus pole of the battery when 
maintenance or service work inside the UPS is necessary. 

z

  The mains socket outlet that supplies the UPS shall be installed near 

the UPS and shall be easily accessible.

 

z

  In case smoke is found coming out from the device, please cut off the 

power supply quickly and contact the distributor.

 

z

  Do not keep or use this product in any of the following environments:

 

9

 

Any area with combustible gas, corrosive substance or heavy 
dust. 

9

 

Any area with extraordinarily high or low temperature (above 
40˚C or below 0˚C) and humidity of more than 90%. 

9

 

Any area exposed to direct sunshine or near any heating 
apparatus. 

9

 

Any area with serious vibrations. 

9

 Outdoor. 

 

z

  In the event that there is fire occurring in the vicinity, please use 

dry-power extinguishers. The use of liquid extinguishers may give rise 
to the danger of electric shock. 

 

 
 

Summary of Contents for MaxPower 1000










Reviews: