manualshive.com logo in svg

Centrales LCD7023PBAB0, Service Manual, Page: 16 / 19

Share
Download
Centrales LCD7023PBAB0 Service Manual Download Page 16

15

 

 

Issue

 

 

Rev.

 

 

 

 

 

 

The spinning noise is too large

 

 

 

If the washing machine 

is set horizontally?

 

Yes

 

  

No 

 

 

Set the machine horizontally.

 

 
 

 

 

If the sundries fall off between the 

spin tub and twin-tub

 

Yes

 

 

Clean the sundries

 

 

No

 

 
 

 

If there is different noise 
during the spin-tub running.

 

Yes

 

Add the oil between the bearing and the 
spin-tub. If the bearing is rustiness  it 
must be changed.

 

 
 

 

No

 

 

If the spin-tub fixing screw and 

brake wheel fixing screw is

 

fastened tightly?

 

 

No

 

 
 
 

If the damping spring is fastened 
tightly or crackly?

 

 

 

Yes

 

 
 
 
 
 
 
 

 

No

 

 
 

 

Fasten the screw.

 

 
 
 
 
 
 
 

Adjust or change the damping spring.

 

 

No

 

 
 

 

If there is different noise when 
the motor is running?

 

 

Yes

 

 

Change the spin motor.

 

Model NO: LCD7023PBAB0

 

Service  Manual

 

Summary of Contents for LCD7023PBAB0




















Reviews:

No comments