manualshive.com logo in svg

Central Pneumatic 95658, Assembly And Operating Instructions Manual

Share
Download
Central Pneumatic 95658 Assembly And Operating Instructions Manual Download Page 10

4. 

Attempt to fire the Floor Nailer into a piece of scrap wood to ensure it is    

 

 

disconnected and is incapable of firing any nails/staples.

5. 

With the Blade Guide (26) facing away from you, remove the four Screws (24).     

 

Then remove the Blade Guide to expose the jammed cleat nail/staple.

6. 

Remove the jammed cleat nail/staple.  Then replace the Blade Guide (26), and    

 

four Screws (24).

7. 

Reload the tool with cleat nails/staples.  Then, reconnect the air supply hose to    

 

the tool.

8. 

Press the Blade Guide (26) against a piece of scrap wood, and test fire the   

 

 

Floor Nailer several times while checking for proper operation.  If the tool is  

 

 

properly firing, you may continue using the tool.  If the tool fails to perform    

 

 

properly, immediately discontinue use and have the tool repaired by a qualified    

 

service technician.

9. 

When finished working, disconnect the air supply.  Remove the cleat nails/   

 

 

staples.  Then, store the tool in a clean, dry, safe location out of reach of children.

Anytime inspection, maintenance, and cleaning are done FIRST:

  1. 

Disconnect the Floor Nailer from its air supply.

  2. 

Empty the Moveable Magazine (35) completely.

  3. 

Attempt to fire the Floor Nailer into a piece of scrap wood to ensure that it is  

 

 

disconnected and is incapable of firing any nails/staples.

INSPECTION, MAINTENANCE, AND CLEANING

4. 

Inspect the air supply Screen that is located in the Air Plug (55) before each  

 

 

use, and clean or replace as necessary.  Dirt and water in the air supply Screen    

 

are major causes of pneumatic tool wear.  Use a filter in the compressed air  

 

 

system for better performance and longer tool life.  The filter must have adequate  

 

flow capacity for the specific application.

5. 

Clean the external parts of the Floor Nailer with a clean cloth and mild detergent   

 

or non-flammable solvent.  Then, dry.

6. 

Store the tool in a clean, dry, safe location out of reach of children.

7. 

      CAUTION:  All maintenance, service, or repairs not listed in this manual   

 

are only to be attempted by a qualified service technician.

SKU   97586

 

95658  

      

For technical questions, please call 1-800-444-3353  

        PAGE 10

Summary of Contents for 95658














Reviews:

No comments

Brands by name

Popular brands

Load more brands