background image

SKU 98524 

For technical questions, please call 1-800-444-3353. 

Page 8

SPECIFICATIONS

Electrical Requirements 120 V~ / 60 Hz / 15 A
Motor (Cutter head) 

Speed

8,000 RPM, 16,000 

cuts per minute 

Maximum Cutting Depth 3/32” 
Stock Capacity

13” W x 6” H

Cutting Blades

Two 13-1/8” L

Feed Speed

23 Feet per Minute

Dust Port Opening

2-3/16” I.D.

Included Accessories

1 Hex Wrench (4mm) 

2 Magnets 

1 Dust Bag

UNPACKINg

When unpacking, check to make sure 

that the item is intact and undamaged.  If 

any parts are missing or broken, please 

call Harbor Freight Tools at the number 

shown on the cover of this manual as soon 

as possible.

INSTRUCTIONS FOR 

PUTTINg INTO USE

  Read the ENTIRE ImPORTANT 

SAFETY INFORmATION 

section at the beginning of this 

manual including all text under 

subheadings therein before set 

up or use of this product.

 

TO PREVENT 

SERIOUS INjURY 

FROm ACCIDENTAL 

OPERATION: 

Turn the Power Switch of the 

tool to its “OFF” position and 

unplug the tool from its 

electrical outlet before 

assembling or making any 

adjustments to the tool.

Note:

  For additional information regarding 

the parts listed in the following pages, 

refer to the Assembly Diagram near 

the end of this manual.

Assembly

Select an area with enough room to 

1. 

fit the chosen dust collection system.  

Select a workbench to mount the 

Planer.  Place the Planer on a work-

bench able to support the weight of 

the Planer and the wood stock being 

planed. The orientation of the Planer 

should enable the easy entry and exit 

of long pieces of wood stock.
Using a pencil, mark through the 

2. 

mounting holes of the Planer, onto 

the workbench. Slide the Planer 

aside and drill four 3/8 inch mounting 

holes into the workbench.  

 

Before drill-

ing, verify that there are no utility 

wires or other obstructions under 

the workbench.

Slide the Planer back over the mount-

3. 

ing holes in the workbench, and se-

cure the Planer to the workbench with 

bolts, washers, spring washers and 

nuts (not included). Securely tighten.

Handle (4)

Head

Screw (1)

Summary of Contents for CENTRAL MACHINERY 98524





















Reviews:

Related manuals for CENTRAL MACHINERY 98524