Central Machinery 96500 Assembly And Operation Instructions Manual Download Page 8

Page 8

SKU 96500

for technical questions, please call 1-800-444-3353.

mark.  Use a siphon to avoid spilling the oil.  Carefully screw the Dip Stick back into 
the Engine crankcase.

Check Air Filter (75) (See illustration above, right).  Unscrew Air Filter Housing Nut and 
remove the Air Filter Housing and Filter Elements.  If dirty or dusty, clean (refer to the 
Maintenance Section).

caution:

 To  avoid  damaging  the  Engine,  never  run  it  without  the  Air  Filter  assembly  at-

tached.

Remove the debris filter, clean, and replace it before filling.  Remove the Fuel Cap (85) 
and fill the Fuel Tank (87) outdoors, with up to 0.95 of a gallon of unleaded gasoline 
containing at least 86 octane.  Do not top-off tank.  Replace Fuel Cap.  Clean up any 
spilled gas with a dry cloth.

    

fire hazard!

  Do not fill Fuel Tank when the Engine is running, or near a pilot light or 

open flame.  Do not smoke.  Do not operate the Engine if gasoline has been spilled.  
Clean spilled gasoline before starting the engine. 

starting the engine

During this procedure, it may be helpful to refer to the photos of the Engine Controls on 
page 6.

Push the Fuel Valve to the open (right) position.  

Close the Choke by pulling it to the left.  

note:

 If the Engine is already hot, it is not necessary to close the Choke.

3.

4.

1.

2.

Summary of Contents for 96500





















Reviews: