Central Machinery 93815 Assembly And Operating Instructions Manual Download Page 13

Warning: Be sure to dispose of the dirty oil properly. Take it to your local waste oil
recycling center. Never dump it on the ground or mix it with trash.

Refilling the Hydraulic Oil
1. Periodically check the level of the oil. It must  be between the two notches on the

lower end of the Dip Stick. If the oil level is low, refill using a recommended oil.

Sharpening the Wedge
1. After long periods of operation, and when required; sharpen the wedge using a

fine-toothed file and carefully removing any burrs or flat spots on the edge.

HOW TO FREE A JAMMED LOG

1. Release both controls, so that the LOG PUSHER (49A) will be fully retracted.
2. Insert a triangular wedge of wood under the log, and activate the log pusher to push

the wedge under the jammed log.

3. Repeat this process using progressively larger wedges, until the jammed log is

freed.  Warning: Never hammer on the jammed log, or place your hands near the log
when attempting to free it.

SKU 93815

PAGE 13

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTUER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER.  THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.

PLEASE READ THE FOLLOWING CAREFULLY

Summary of Contents for 93815

















Reviews: