Description
Part #
Qty
Fuzzies, (pair)
101-022
1
Foot Strap, Cotton, 24” quick link
607-548
1
Foot Strap, Cotton, 27” quick link
210-130
1
Belly Strap
210-034
1
Wood, Roll Down Bar, 23” Outside Hooks
607-127
1
Cotton Web, CL
607-330
2
Trapeze Sling, CL
607-331
1
Loops, Single Dring, CL (pair)
607-346
1
safety Strap, CL
607-355
1
Wing Knob
GEN9371
4
Sliding PTB, Wood, CL
607-461
1
Shoulder Bolt, Sliders
619-203
2
Spring, Trap, Green
SPR9000
1
Spring, Trap, Red
SPR9001
1
Spring, Trap, Blue
SPR9004
2
Spring, White
SPR9238
2
Spring, Trap, Grey, CL
SPR9245
2
Spring Trap, Long Red
SPR9246
2
Bottom Frame w/Mat Assembly
N/A
1
Trapeze CL Canopy Top Assembly
N/A
1
Vertical Slider Assembly, CL
N/A
1
Trapeze Bar Assembly
17803
1
PTB Slider Assembly
N/A
2
Head End SS Tubes
TRP0110
2
Foot End SS Tubes
TRP0111
2
Wrench, 21mm x 1/2”
ALL0060
1
1/8” Cotter Pin
216-000
4
3/16” Allen Wrench
GEN9280
1
ASSEMBLY
»
Using the provided 3/16” allen wrench, loosen the set screws in each
of the eight flange connectors mounted to the outside of the frame.
Remove the two vertical tubes from the box and the sliding push
thru bar system. Lay the tubes down so the holes on the sides of the
tubes face away from each other. Take the sliders of the push thru
bar (PTB) and slide them over the tubes opposite the end with the
eye bolts, you will need to pull the knobs of the sliders out to move
the sliders up the tubes. Continue to move the sliders up the tubes
until the pins lock into the bottom set of the three holes in the tube.
Make sure both sliders are locked into the same bottom holes. Insert
the provided cotter pins into each of the 1/8” holes near the bottom
ends of the tube. Pick up this assembled tube set, be careful of the
PTB, it may swing; place the assembly in the flanges on the head
end of the machine (the end with the vinyl flaps). Be carefully of the
cotter pins so they do not scratch the vinyl or wooden frame. The
cotter pins will automatically set the tubing height.
Insert the provided cotter pins into each of the 1/8” holes near
the bottom ends of the other two vertical tubes. Pick up the tube
assembly with the vertical slider and place the tube ends into the
flanges on the foot end of the frame.
»
With help, place the rectangular section on top of the vertical tubes.
Make sure all 4 corner fittings fit securely onto the tubes.
Note:
Set the rectangle on the vertical tubes so that the safety strap
and the push-thru bar are on the same end.
»
Using the 3/16” allen wrench, tighten the set screws in the corner
fittings and in the flanges around the frame. After tightening all
set screws in all the corner angles, test the movement of the sliding
push thru bar. To do this pull the knobs of the sliders out and start
sliding the PTB up or down. This system should move easily and not
stick when uniform pressure is applied on each side. If the sliders
stick when moving the position, simply loosen the set screws that
are holding the vertical poles, rotate the tubes as necessary until the
sliders move freely. Be sure to re-tighten all set screws. Remove the
cotter pins from the tubes and save for future use.
HOW TO ADJUST YOUR SLIDING PUSH THROUGH BAR
Position your hands on the outside of each slider. Place your middle
and/or ring fingers under the silver base of the knob; right where the
black body of the knob threads into. Place your index finger and thumb
around the knob itself. Pull each of the knobs outwards, away from the
vertical tubes, until they stop. Using the same force on each arm, move
the slider upwards or downwards to each new location. Once you near a
new location slightly release the outward pull of the knobs. The pins will
automatically fall into the next position when aligned.
WEEKLY MAINTENANCE
Inspect springs for separations, and replace if needed. Inspect snaps
on springs and make sure the retractors operate smoothly. Replace
them if worn or they do not operate freely. Make sure that there are no
indentations on the inside of the hooks. Inspect all nuts, eyebolts and
setscrews for tightness. Tighten or replace if necessary.
It is recommended to check to ensure the pins in the plunger knobs
protrude and lock into the vertical tubes. First pull both knobs out and
start moving the sliders to a different position. Release the knobs
before the next hole and continue to slide the system. Once over a hole
the pin of the knob will drop into the opening. Once each slider is in a
new position apply a down force on the PTB directly downwards. The
pins of the sliders should not come out of the holes. If the pins do not
stay in the tube holes, the pull knobs need to be replaced; call Balanced
Body for replacement parts.
WARNING:
This machine is potentially dangerous, and Balanced Body®
assumes no liability towards use or misuse. If you are not fully aware of
the safety issues and use of this machine, do not use it. Use only with
qualified instructor supervision.
QUESTIONS?
Call Balanced Body at 1-800-PILATES (1-800-745-
2837) or 916-388-2828.
3
