background image

The following procedure should be used to adjust the Speed Gain Trimpot: 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 

1) 

Set the motor speed to 5-10% of maximum speed. 

2)  Apply a load to the motor and observe if the speed 

increases or decreases. 

3) 

Remove the load. 

4) 

If speed increases under load, turn the trimpot counter-
clockwise. 

 

If speed decreases under load, turn the trimpot 
clockwise. 

5)  Repeat steps 2 through 4 until there is no observable 

change in speed when load is applied or removed. 

 
Note: if the motor oscillates when step 1 is attempted, turn the 

trimpot counter-clockwise until the motor runs smoothly; 
then proceed with steps 2-5. 

 

(3) MOUNTING PLATE 

 

The CN0121A is a linear amplifier. As a consequence it may dissipate considerable heat 
while running large motors at low speed under heavy load. This heat may cause damaging 
temperatures in the CN0121A. For this reason it is extremely important to properly heat sink 
the drive. 
 
Mount the CN0121A on a finned aluminum heat sink using thermal compound between the 
CN0121A and the heat sink. If needed, use a fan to force air over the heat sink. Monitor the 
case temperature of the CN0121A under the worst case motor load conditions. Do not let the 

case temperature exceed 70

°

C (158

°

F). 

Summary of Contents for CN0121A








Reviews: