Page 2
For technical questions, please call 1-888-866-5797.
Item 63603
Specifications
Electrical
Requirements
Voltage Range: 6VDC and 12VDC
Lead Wire Length: 60 IN.
Bulb: 12VDC / 3 W
Clamp Capacity: 20 AMP
Save This Manual
Keep this manual for the safety warnings and
precautions, assembly, operating, inspection,
maintenance and cleaning procedures. Write the
product’s serial number in the back of the manual near
the assembly diagram (or month and year of purchase
if product has no number). Keep this manual and the
receipt in a safe and dry place for future reference.
Important Safety Information
General Power Tool
Safety Warnings
WARNING Read all safety warnings
and instructions.
Failure to follow the warnings
and instructions may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions
for future reference.
1.
Work area safety
a.
Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b.
Do not operate tools in explosive atmospheres,
such as in the presence of flammable liquids,
gases or dust.
The connection may create
sparks which may ignite the dust or fumes.
c.
Keep children and bystanders
away while operating the tool.
Distractions can cause you to lose control.
2.
Electrical safety
a.
Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of
electric shock if your body is grounded.
b.
Do not expose the tool to rain or wet
conditions.
Water entering a tool will
increase the risk of electric shock.
c.
Do not abuse the cord. Never use the cord
for carrying, pulling or disconnecting the
tool. Keep cord away from heat, oil, sharp
edges or moving parts.
Damaged or entangled
cords increase the risk of electric shock.
3.
Personal safety
a.
Stay alert, watch what you are doing and use
common sense when operating a tool. Do not
use a tool while you are tired or under the
influence of drugs, alcohol or medication.
A moment of inattention while operating a
tool may result in serious personal injury.
b.
Use personal protective equipment.
Always wear eye protection.
Safety
equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c.
Do not overreach. Keep proper footing and
balance at all times.
This enables better control
of the power tool in unexpected situations.
d.
Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from electrical parts.
Loose clothes,
jewelry or long hair can be caught in parts.
e.
Only use safety equipment that has been
approved by an appropriate standards
agency.
Unapproved safety equipment
may not provide adequate protection.
Eye protection must be ANSI-approved and
breathing protection must be NIOSH-approved
for the specific hazards in the work area.
4.
Power tool use and care
a.
Store idle tools out of the reach of children and
do not allow persons unfamiliar with the tool
or these instructions to operate the tool.
Tools
are dangerous in the hands of untrained users.
b.
Maintain tools. Check for misalignment
or binding of parts, breakage of parts and
any other condition that may affect the
tool’s operation. If damaged, have the
tool repaired before use.
Many accidents
are caused by poorly maintained tools.
Circuit Tester Safety Warnings
1. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing, contact
Harbor Freight Tools for a replacement.
2. Avoid unintentional starting. Prepare to
begin work before connecting the tool.
3. Use as intended only.
4. Inspect before every use; do not use
if parts are loose or damaged.
5. Do not leave the tool unattended when it is
connected to an electrical source. Disconnect the
tool from its electrical source before leaving.
6. This product is not a toy.
Keep it out of reach of children.
