manualshive.com logo in svg

CEM DT-337, Operating Instruction, Page: 12 / 13

Share
Download
CEM DT-337 Operating Instruction Download Page 12

 

11 

 

Data Hold 

To freeze the LCD meter reading, press the data hold 

button. The data hold button is located on the left side of the 

meter (top button). While data hold is active, the 

HOLD

 

display icon appears on the LCD. Press the data hold button 

again to return to normal operation. 

Note: The HOLD feature will activate when the Backlight is 

turned on. Press the HOLD key again to exit Hold

. 

 
Backlight 

Press and hold the HOLD    key for >1 second to turn 

on or off the display backlight function.  

Note: The HOLD feature will activate when the Backlight is 

turned on. Press the HOLD key again to exit Hold

.

 

 

ZERO BUTTON 

For ACA and Capacitance Zero & Offset adjustment. 

 

Manual Ranging 

The meter turns on in the autoranging mode. Press the 

Range

 button to go to manual ranging. Each press of the 

range button will step to the next range as indicated by the 

units and decimal point location. Press and hold the 

Range

 

button for two seconds to return to autoranging. Manual 

ranging does not function in the AC Current , Diode and 

Continuity check functions 

Battery Replacement 

1.  Remove the one rear Phillips head screw 

2.  Open the battery compartment 

3.  Replace the Requires two “AAA” batteries (UM4 R03)  

Summary of Contents for DT-337














Reviews:

No comments