background image

 

Technical Datasheet 

User’s Manual 

Narrowband multi-channel data radio modem 

LinkWiser

-S400M

 

Cellution Inc. 
#317, NKIC, 48-84 Honguen-1dong, Seodaemun-gu, Seoul, Korea Zip: 120-760 
 
Enquiries: 

[email protected]

 / 

[email protected]

 

Voice: +82-2-3217-4838 / Fax: +82-2-3217-4831 

14

10dBm 

 

Writing: ‘AT+P=8’ // Set the Tx power at 8

th

 level 

Answer: > 

 
Description: Power of the Radio 

Value 

Tx power (dBm) 

8 < 

10dBm 

7 < 

9dBm 

6 < 

7.9dBm 

5 < 

6.3dBm 

4 < 

4.4dBm 

3 < 

2dBm 

2 < 

-1.3dBm 

1 < 

-7.0dBm 

0 < 

-40dBm 

 

12-4-3 RSSI level checking 

Reading: ‘AT+CSQ?’ 

Answer: ‘n’ 

 

Description: ‘n’ is a realistic RSSI level in the unit of ‘dBm’. 
Caution: One time RSSI level reading may not be correct due to circumstances. Thus, more than three 

times of RSSI level readings are recommended. 

 
12-4-4 Destination address setting 

Reading: ‘AT+ADDR?’ 

Answer: ‘n’ // n ranges 0~255 
 

Writing: ‘AT+ADDR=n’ 

 

Description: ADDR means a destination ID, if it is set ‘0’ in the ADDR, the radio enters into the 

Transparent mode. while it is set ‘1~255’ in the ADDR, the radio enters into the Address mode and 

delivers data to the preset destination ID of node only.

 

 

12-5 Timing Chart 

 
12-5-1 Maximum Packet Size 

The LinkWiser accepts 128bytes of packet size of USER DATA only as its one time maximum 

FIFO (First-In-First-Out) is 128bytes. If your packet size (USER DATA) exceeds over 128bytes, then 

you have to split them into several appropriate size of packets with considering the below timing chart 

& air rate. And also you have to put some delay between that divided packet and the packet with 

considering the below timing chart & air rate in order to complete successful transmission. 

 

12-5-2 Timing Chart Overview 
 

Figure1 shows a typical system block diagram comprising hosts (DTE user’s application) connected to 

LinkWiser. Host(A) will be sending and Host(B) will be receiving and processing this data. 

 

Summary of Contents for LinkWiser-S400M


















Reviews: